Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 208

Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 117

Configuration

4-9

Compaq Confidential – Need to Know Required

Writer: Everett Godaire Project: TL891 MiniLibary System User's Guider Comments:

Part Number: ER-TL891-UA.A01 File Name: e-ch4 Configuration Last Saved On: 3/1/99 2:15 PM

The following tables, Table 4-1, MiniLibrary Configuration Options, and
Table 4-2, MiniLibrary Special Configuration Options summarize the
configuration settings for the Mini-Library Base Module.

NOTE:

The options described in Table 4-1 and Table 4-2 represent the version of the

firmware in use when this manual was written. If the displays on your control panel differ
from those described here, you may find an up to date listing of configuration options on
the Compaq Website listed in the front of this manual.

Reference Table 4-1:

*

Designates Default Settings

(1) Applies to Base Module Display

(2) Applies to Expansion Unit Display

Reference Table 4-2:

The default settings are shown in the third column, and other possible settings are
shown in the second column.

«
...
115
116
117
118
119
...
»

Содержание TL891 - DLT Tape Library

















































































































































































































Отзывы:

Нет отзывов