manualshive.com logo in svg

Compaq TL891 - DLT Tape Library, Руководство пользователя, Страница: 182 / 208

Поделиться
Скачать
Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 182

F-2

 TL891 MiniLibary System User's Guide

Compaq Confidential – Need to Know Required

Writer: Everett Godaire  Project: TL891 MiniLibary System User's Guide  Comments: 

Part Number: ER-TL891-UA. A01  File Name: m-appf Addding a Second Tape Drive  Last Saved On: 3/1/99 1:26 PM

1

Magazine door

8

Power supply

2

Door opener/Magazine lock

9

Controller PWB

3

Shuttle Cable

10

AC power switch

4

Shuttle

11

Control panel

5

Shuttle motor

12

Unlock/open switch

6

Drive caddy assembly

13

Unlock/open switch

7

Fan

14

Leadscrew

Overall Procedure

NOTE:

  If the base module is part of an expanded TL89x MiniLibrary subsystem, refer to

the 

TL89x Mini Library Service Manual for information on removing the base module

from the subsystem.

To add a second drive to the base module you must do the following steps.

 

1.

 

Remove the skin cover, if present, using the procedure in this
document.

 

2.

 

Remove the cover plate using the procedure in this document.

 

3.

 

Remove the drive caddy assembly using the procedure in this
document.

 

4.

 

Install the new drive using the procedure described in this document.

 

5.

 

Replace the drive caddy assembly.

 

6.

 

Replace the cover plate.

 

7.

 

Replace the skin cover.

 

Removing and Replacing the Skin Cover (Desktop
Models Only)

 

The skin cover is held in place by two captive screws near the top of the front
panel, and two screws on each side of the base module (Figure F-2).

Содержание TL891 - DLT Tape Library

















































































































































































































Отзывы:

Нет отзывов