Compaq TL891 - DLT Tape Library Скачать руководство пользователя страница 151

Страница: 151 / 208

Diagnostics and Troubleshooting

6-23

Compaq Confidential – Need to Know Required

Writer: Everett Godaire Project: TL891 MiniLibrary System User's Guide Comments:

Part Number: ER-TL891-UA.A01 File Name: g-ch6 Diagnostics and Troubleshooting Last Saved On: 3/3/99 11:54 AM

Table 6-2
Fault Symptom Codes

continued

FSC

Message

Description

6043

Invalid Com Blk Type

A Slave inter-module process received
a packet from the Master inter-module
process, but the packet’s CommBlock
type was invalid.

6044

Invalid Com Blk Type

A Slave inter-module process received
a packet from the Status/Message
queue, but the packet’s CommBlock
type was invalid.

6045

Command Overlap

A Slave inter-module process received
a Command from the Master inter-
module process, but a previously
issued command is still being
executed.

6046

No Pkts To Send

A Slave inter-module process has
been requested to send a packet to
the Master inter-module process, but
the Slave inter-module process has no
packets to send.

6047

Invalid Direction

A Slave inter-module process has
received a direction control byte from
the Master inter-module process, but
the direction control byte is invalid.

6048

Master Pkt ID Bad

B001

Boot ROM CRC Error

B002

Boot RAM Test Failed

B004

Boot Comm Open Error

B005

Boot Novram Error

B006

Boot Unused Int

B007

Flash Init Error

B010

Boot UART 0 Error

continued

Содержание TL891 - DLT Tape Library

















































































































































































































Результаты поиска

Содержание TL891 - DLT Tape Library

Отзывы:

Compaq TL891 - DLT Tape Library, Руководство пользователя, Страница: 151 / 208

Результаты поиска

Содержание TL891 - DLT Tape Library

Отзывы: