CognitiveTPG A776II Скачать руководство пользователя страница 39

Страница: 39 / 46

Chapter 5: Troubleshooting

A776II Two-Color Thermal/Impact Hybrid Printer: User Guide

A776 2UG0001 B 11/2016

Knife does not operate

Condition

Possible causes

What to do

Receipt is not cut.

Paper is jammed.

Open the receipt cover, inspect the

knife, and clear any jammed paper.

All other problems.

Contact a service representative.

Other conditions

The following problems all need to be corrected by a qualified service representative.
See the section below, “Contacting a service representative.”

•

MICR check reader not operating properly

•

Forms not feeding into the slip/forms area properly

•

Missing dots in slip or forms printing

•

Printer will not cycle or stop when required

•

Illegible characters

Contacting a service representative

For serious problems, such as the printer not printing, not communicating with the host
computer, or not turning on, contact CognitiveTPG technical support at 1(800)732-8950,
extension 4.

•

Paper will not feed

•

Knife will not cycle or cut

•

Platen will not open or close

•

Printer will not communicate with the host
computer

Returning a printer

Follow the instructions in Chapter 3 if you need to return a printer for servicing.

Содержание A776II















































Результаты поиска

Содержание A776II

Отзывы:

Похожие инструкции для A776II

Бренды по названию

Популярные бренды

CognitiveTPG A776II, Руководство пользователя

Результаты поиска

Содержание A776II

Отзывы:

Похожие инструкции для A776II

Бренды по названию

Популярные бренды