background image

22

Chapter 3:  Settng up the Printer 

A776II Two-Color Thermal/Impact Hybrid Printer: User Guide 

A776 2UG0001 B   11/2016

• 

Print head setting
This is the print head energy rating. It must match 
the rating marked on the front right of the thermal 
mechanism in the printer. 

CAUTION

Do not change print head setting unless print head is 
replaced. 

When a new thermal mechanism is installed, be sure 
this setting matches the indicated energy rating 
on the mechanism. (See 

A776II Service Guide

 for 

replacing the thermal mechanism.)

• 

Color density
The color density setting adjusts the energy level at 
the print head to change color printing or to adjust 
to paper variations. The factory setting is 100%.

CAUTION

Choose an energy level no higher than necessary to 
achieve a dark printout. Failure to observe this rule 
may result in a printer service call or voiding the printer 
warranty. Running at a higher energy level reduces the 
life of the print head.  Contact CognitiveTPG technical 
support if you have any questions.

• 

Print density (monochrome papers only)
Adjusts print head energy level to darken printout 
or adjust for paper variations.  When the printer 
prints high-density color print lines (text or 
graphics), it automatically slows down. Factory 
setting is 100%.

• 

Alternate reset feature
This feature allows you to reset the A776II by 
opening and closing the front cover instead of using 
the reset button.

• 

Paper low sensor
Allows the user to enable or disable the paper low 
sensor.

• 

MICR 
Allows the user to enable or disable the MICR to 
read checks. 

• 

MICR dual pass option
This feature when enabled allows the printer 
to attempt a second reading of the check MICR 
number, if the first attempt was unsuccessful.

Select the hardware options to set: 

CAUTION

Choose a print density setting no higher than 
necessary to achieve acceptable print density. Failure 
to observe this rule may result in a printer service call 
and may void the printer warranty. Running at a higher 
energy level reduces the print head life. Consult your 
CognitiveTPG technical support specialist if you have 
questions.

Содержание A776II















































Отзывы: