CognitiveTPG A776II Скачать руководство пользователя страница 35

Страница: 35 / 46

Chapter 5: Troubleshooting

A776II Two-Color Thermal/Impact Hybrid Printer: User Guide

A776 2UG0001 B 11/2016

Printer beeps

Condition

Possible causes

What to do

Printer beeps in a single, double, or

The printer has a problem

Contact a service representative.

triple pattern at first power on.

with its electronics.

The online paper status error light
blinks in the same pattern, and the
printer won’t power up.

Printer beeps during normal

The printer may be programmed

Consult your application software

operation.

to beep during normal operation

manual.

by the software application used

on the host computer.

Printer will not print

Condition

Possible causes

What to do

The online paper status error light

The receipt paper may be out, the

Check that the receipt paper is properly

blinks and the printer won’t

cover open, the knife jammed, the

loaded and covers are closed. See the

print.

supply voltage out of range, or the

table on page 31. If the problem

print head temperature out of range.

continues, contact a service representative.

Printer has no power (light not on)

Power supply may be defective.

If the power supply is plugged in but
does not come on, you need to order a
new power supply. Contact a service
representative.

Printer has power, doesn’t

Cables may not be connected

Check all cable connections. Check

print properly.

that the host computer and power

supply are both on (the power supply

is turned on by plugging it into a live

outlet). Look for the green power light

to show that the printer has power .

See “Connect the cables” on page

11.

All other causes.

Contact a service representative.

Содержание A776II















































Результаты поиска

Содержание A776II

Отзывы:

Похожие инструкции для A776II

Бренды по названию

Популярные бренды

CognitiveTPG A776II, Руководство пользователя

Результаты поиска

Содержание A776II

Отзывы:

Похожие инструкции для A776II

Бренды по названию

Популярные бренды