background image

Pas sen ger Com part ment Con nec tions (Con tin ued)

  Door Trig ger/In te rior Light Sup ply (Con tin ued)  

NOTE: Clif ford Elec tron ics’ web site for Autho rized Clif ford Deal ers has

de tailed de scrip tions of wire col ours and lo ca tions for most for eign and

do mes tic ve hi cles.  In stal la tion dia grams and pro gram ming pro ce dures for

older Clif ford prod ucts are also avail able.  Just go to

www.clif ford deal ers.com for as sis tance 24- hours per day.

  Door Locks  

WARN ING: If the power door locks do not op er ate prop erly when the sys tem

is armed and dis armed, DO NOT USE THE VE HI CLE’S DOOR LOCK SWITCH!  If

the con trol unit’s door lock wires are mis wired, per ma nent dam age to the

con trol unit or to the car’s elec tri cal sys tem and door lock ser vos will re sult.  If 

you re quire as sis tance, call the Clif ford Tech ni cal Sup port Helpline PRIOR to

wir ing the door locks.

Tazor 4 systems provide power door lock interface capabilities and are able to in ter face with

any power door lock con figu ra tion in clud ing some Mer cedes Benz and Audi ve hi cles that

re quire a 3- second lock pulse (pulse du ra tion is installer- programmable) and with any car

(VW’s and Nissans, for example) that require double unlock pulse.  If the ve hi cle is not

equipped with power door locks, you may op tion ally add up to four #60- 516 Door Lock

Ser vos. 

When adding an IntelliStart 4 to the Tazor 4, it is recommended that RPM-depending door

locking be selected.  The RPM-dependent door locking feature is only available with the

addition of the IntelliStart 4.

De ter min ing the Door Lock Sys tem Type

1. Remove the door lock switch on the driver’s side of the vehicle to reveal the switch wires.

a. If there are four or more wires, make the connections shown in Diagram 4 for

reverse polarity.

b. If there are three wires, proceed to step 2.

c. If the vehicle is a Nissan and it does not have a door lock switch, find the single

wire in the driver’s kick panel that shows ground when the locks are unlocked and

“open” when the locks are locked.  Cut this wire and make the connections shown

in Door Lock/Unlock Diagram 3.

2. Connect the negative voltmeter lead to ground and probe each wire while

locking/unlocking.  If the voltmeter show +12v while activating the switch, make the

connections shown in Door Lock/Unlock Diagram 1 for positive trigger.  Otherwise, go to

step 3.

3. Repeat step 2 with the negative voltmeter lead connected to +12v.  If the voltmeter

shows +12v while activating the switch, make the connections shown in Door

Lock/Unlock Diagram 2 for negative trigger.

4. Locks controlled from the driver’s door key require installation of just one #60-516 servo

in the driver’s door.  Vehicles without factory power locks require a servo in each door. 

Mount the servo(s) and make the connections shown in Door Lock/Unlock Diagram 5 for

adding servos.

5. On a vacuum-pump-type Mercedes Benz or Audi, make the connections shown in Door

Lock/Unlock Diagram 6, then (if 1989 or older) program the system for a 3-second lock

pulse.

6. The Tazor 4 can also provide two pulses (+ or -) for lock and/or two pulses (+ or -) for

unlock required by some vehicles (such as some Nissans, VW’s, and Audis).  Wire the

door locks following the steps above and select the 2x lock or unlock feature in

installer-programming.

6

Содержание Tazor 4




























Отзывы: