ClearSpan 115408 Скачать руководство пользователя страница 3

Страница: 3 / 23

CLEARSPAN

™

END WALL FRAMING KITS

Revision date: 10.04.16

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all necessary

parts

before

you begin.

1. Unpack the shipment and place where you can easily

inventory parts. Refer to the Bill of Materials/Spec

Sheets.

2. Verify that all parts listed on Bill of Materials/Spec

Sheets are present. If anything is missing or you have

questions, consult the Pictorial Parts Guide and all

shelter diagrams for clarification, or contact Customer

Service.

NOTE:

At this time, you do not need to open plastic

bags containing smaller parts such as fasteners and

clamps.

QUICK START GUIDE

For a quick overview of the end frame and its components,

consult the Quick Start section at the back of this guide.

Space below is reserved for customer notes.

Содержание 115408
























Результаты поиска

Содержание 115408

Отзывы:

Похожие инструкции для 115408

Бренды по названию

Популярные бренды

ClearSpan 115408, Руководство пользователя

Результаты поиска

Содержание 115408

Отзывы:

Похожие инструкции для 115408

Бренды по названию

Популярные бренды