manualshive.com logo in svg

Clarke PRO-MIST DURA, Инструкция и список запасных частей, Страница: 13 / 133

Поделиться
Скачать
Clarke PRO-MIST DURA Скачать руководство пользователя страница 13

10

PRO-MIST DURA® ULV

4C

6C

5C

2C

1C

3C

Mounting a Battery on the Pro-Mist Dura for 

Self-Contained Operation

You can expect a couple hours of operation from one 
fully charged medium sized (size 24M )12 volt Deep  
Cycle battery. An expansion battery base option is  
available to expand and increase the machine's on board 
battery capacity. Using the sprayer with its own battery 
allows the sprayer to be quickly mounted on any vehicle, 
even vehicles without an electrical system. We strongly 
recommend the use of a deep-cycle, hi-capacity, high 
quality RV/Marine battery. This type of battery will  
best handle the stress of repeated charging and  
discharging. Eventually the battery will no longer have 
the required power to maintain high speed rotation. The 
machine will then shut down the  
spray head. 

The Battery Box located on the Blower Stand Base  
is designed to hold up to a size “24M” marine battery.  
A short power cord with plug is provided to connect  
this onboard battery to the blower stand power plug.  
Be careful to observe proper polarity. The Red lead is 
connected to the positive (+) battery terminal, and  

the black lead is connected to the negative (-)  
battery terminal, Observe the Polarity markings  
on the plugs housing.

INSTALLATION

CAUTION: 

Do not connect until final step of  

electrical installation.

Содержание PRO-MIST DURA






































































































































Отзывы:

Нет отзывов