manualshive.com logo in svg

Clarke CA90 32T, Руководство по обслуживанию, Страница: 60 / 62

Поделиться
Скачать
Clarke CA90 32T Скачать руководство пользователя страница 60

Wheel System, Traction

60

Service Manual – CA90 32T

Trigger Switch

1.  Disconnect the batteries.

2.  Remove the (4) screws from the upper control housing panel (dash board), and the (4) screws from the 

lower control housing panel.

3.  GENTLY move them aside to gain access to the inside of the control housing. (See picture above)

4.  Use a needle nose pliers (needle nose vice grips work the best) to hold the nylock nut on top of the 

switch.  Reach up with a #1 phillips screwdriver to unscrew the screw.  Repeat this for the other nut and 

screw.  NOTE:  The 3 mm screws strip easily, so be careful.

5.   Swing the switch with wires still connected into a position where you can dis-connect/re-connect the 

wires from the switch.

6.  Note that the switch information printed on the switch is away from you (facing down).

7.  One at a time, dis-connect the wires from the old switch and re-connect them to the new switch.

8.  Reinstall the switch in the reverse order of the steps above.

Содержание CA90 32T































































Отзывы:

Нет отзывов