Cisco Nexus 9396PX Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 74

background image

The power supplies are rated to output up to 650 W (AC power supplies) or up to 930 W (DC power supplies),
but the switch requires less than those amounts of power from the power supply. To operate the switch, you
must provision enough power from the power source to cover the requirements of both the switch and a power
supply. Typically, this switch and a power supply require about 232 W of power input from the power source,
but you must provision as much as 455 W power input from the power source to cover peak demand.

Some of the power supply modules have Underwriter Labs (UL) rating capabilities that exceed the switch
requirements. When calculating your power requirements, use the switch requirements to determine the amount
of power that is required for the power supplies.

Note

To minimize the possibility of circuit failure, make sure that each power-source circuit that is used by the
switch is dedicated to the switch.

For AC input application, please refer to the following statement:

Note

Statement 1005—

Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the
protective devices are rated not greater than 20A (North America), 16A (Europe), and 13A (UK).

Warning

For DC input application, please refer to the following statement:

Note

Statement 1005—

Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent) protection.

• Ensure that the protective devices are rated not greater than 40A when the switch is powered with regular

DC power supplies (rated 48-60VDC).

• Ensure that the protective devices are rated not greater than 10A when the switch is powered with HVDC

power supplies (rated 240-350VDC).

Warning

For the power cables to use with the power supplies, see

Power Cable Specifications, on page 51

Note

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

8

Preparing the Site

Planning for Power Requirements

«
...
16
17
18
19
20
...
»

Содержание Nexus 9396PX











































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 9396PX

Бренд: D-Link Страницы: 36

Бренд: X10 Страницы: 20

Бренд: Lantronix Страницы: 2

Бренд: Vector Страницы: 6

EdgeSwitch 10 XP

Бренд: Ubiquiti Страницы: 13

Raritan Dominion LX II

Бренд: LEGRAND Страницы: 7

Бренд: StarTech.com Страницы: 16

Бренд: Datavideo Страницы: 64

Бренд: C4i Страницы: 7

Бренд: Wyrestorm Страницы: 4

EXT-HDMI-CAT5-844

Бренд: Gefen Страницы: 28

Sun Datacenter InfiniBand Switch 36

Бренд: Sun Oracle Страницы: 12

B-520-MTRX-230-6x4+2

Бренд: Binary Страницы: 32

Бренд: W&T Страницы: 40

SW-UNM-8FE1GC-8POE

Бренд: MO-EL Страницы: 9

Бренд: Analog way Страницы: 4

Бренд: KTI Страницы: 157

MegaTouch USB-802 Series

Бренд: Vetra Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды