Cisco Nexus 9396PX Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 74

background image

3.

Strip 0.6 inches (15 mm) of insulation off the DC wires that you are using.

4.

Orient the connector as shown in the following figure with the orange plastic button on top.

-48V (-DC) cable

4

Wire retainer lever

1

Grounding cable (8 AWG recommended)

5

Orange plastic button on top of the connector

2

-48V Return (+DC) cable

3

5.

Use a small screwdriver to depress the spring-loaded wire retainer lever on the lower spring-cage wire connector.
Insert your green (ground) wire into the aperture and then release the lever.

6.

Use a small screwdriver to depress the spring-loaded wire retainer lever on the middle spring-cage wire connector.
Insert your black (DC negative) wire into the aperture and then release the lever.

7.

Use a small screwdriver to depress the spring-loaded wire retainer lever on the upper spring-cage wire connector.
Insert your red (DC positive) wire into the aperture and then release the lever.

8.

Insert the connector block back into the power supply. Make sure that your red (DC positive) wire aligns with
the power supply label, "+ DC".

If you require

n

+

n

redundancy, be sure that each power supply is powered by a different power source.

Note

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

26

Installing the Chassis

Powering Up the Switch

«
...
34
35
36
37
38
...
»

Содержание Nexus 9396PX











































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 9396PX

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

Anaconda Switcher VK68A

Бренд: X10 Страницы: 2

MIEN2208 Series

Бренд: Maiwe Страницы: 5

Бренд: C4i Страницы: 7

TK-407K - KVM Switch - USB

Бренд: TRENDnet Страницы: 2

Cutler-Hammer RTHMFDA20100WSU

Бренд: Eaton Страницы: 28

Бренд: ATEN Страницы: 21

Бренд: Gefen Страницы: 9

Бренд: GoMax Electronics Страницы: 6

OBERON C SOUND HUB COMPACT

Бренд: Dali Страницы: 3

Бренд: Gigabyte Страницы: 2

Бренд: Solar Solve Marine Страницы: 12

Бренд: J-Tech Digital Страницы: 8

Бренд: Eaton Страницы: 4

SuperStack II Switch 3300

Бренд: 3Com Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды