Cisco Nexus 9396PX Скачать руководство пользователя страница 13

Страница: 13 / 74

Screw holes (2) for attaching a front-mount
bracket for four-post racks (one bracket on each
of two sides)

48 1- and 10-Gigabit Ethernet Small Form-Factor
Plugable (SFP+) optical ports (supporting
1-Gigabit and 10-Gigabit speeds) to Application
Policy Infrastructure Controllers (APICs)

To determine which transceivers, adapters, and cables are supported by this switch, see the

Cisco Transceiver

Modules Compatibility Information

document.

The following figure shows the hardware features seen from the fan side of the chassis.

Chassis LEDs are as
follows:

• Beacon (BCN)

• Status (STS)

Screw holes (2) for
attaching the grounding
lug.

Screw holes (4) for
attaching a center-mount
rack bracket for two-post
racks (one bracket for
each of two sides).

Notch in both sides of the
chassis for locking the fan
end of the chassis to the
bottom-support rails.

Screw holes (2) for
attaching a front-mount
bracket for 4-post racks (1
bracket on each of 2
sides).

Two power supply
modules (AC power
supply shown)

Power supply slots are
numbered 1 on the left
and 2 on the right (as seen
when looking at the power
supplies).

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

Overview

Содержание Nexus 9396PX











































































Результаты поиска

Содержание Nexus 9396PX

Отзывы:

Похожие инструкции для Nexus 9396PX

Бренды по названию

Популярные бренды

Cisco Nexus 9396PX, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 9396PX

Отзывы:

Похожие инструкции для Nexus 9396PX

Бренды по названию

Популярные бренды