Cisco Nexus 9396PX Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 74

background image

Step 1

Pull the power cord out from the power receptacle on the power supply to be removed and verify that the

LED turns

off.

The

LED might be on and amber colored to indicate that the input power has been disconnected.

Note

Step 2

Remove the power supply from the chassis by pushing and holding its thumb latch to the left and pulling the power supply
part way out of the chassis.

Step 3

Place your other hand under the power supply to support it while you slide it out of the chassis.

Either place the power supply on an antistatic surface or pack it in its packing materials.

Step 4

If the power supply slot is to remain empty, install a blank power supply filler panel (part number N2200-P-BLNK).

What to do next

You are ready to install the replacement power supply.

Removing a DC Power Supply

You can remove one power supply while the other one provides power to the switch.

To disconnect the power supply from its power cables, you must shut off the power from the power source
and then either disconnect a connector for the power cables or release each of three cables from the power
supply (requires a standard screw driver).

Step 1

Turn off the circuit breaker for the power feed to the power supply that you are replacing.

Be sure that the LEDs turn off on the power supply that you are removing.

Step 2

Remove the power cable from the power supply by doing the following:

• To remove an orange power cable connector from a 48-V DC power supply, do the following:

1.

Push the orange plastic button on the top of the connector block inward toward the power supply.

2.

Pull the connector block out of the power supply.

Step 3

Grasp the power supply handle while pressing the release latch towards the power supply handle.

Step 4

Pull the power supply out of the bay.

What to do next

You are ready to install a DC power supply in the open slot.

Installing an AC Power Supply

You can replace one power supply while the other one provides power to the switch.

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

39

Replacing Modules

Removing a DC Power Supply

«
...
47
48
49
50
51
...
»

Содержание Nexus 9396PX











































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 9396PX

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

Бренд: I/O Interconnect Страницы: 27

MicroHub GUH274W3

Бренд: IOGear Страницы: 1

Бренд: TRENDnet Страницы: 12

Бренд: Clever Little Box Страницы: 15

Бренд: Tripp Lite Страницы: 12

QuantaMesh T4000 Series

Бренд: QCT Страницы: 41

Бренд: Eaton Страницы: 36

Бренд: ABM Страницы: 8

Palert PX-01 Series

Бренд: JenLogix Страницы: 48

Plug in Digital Time Switch

Бренд: Grasslin Страницы: 88

Бренд: InvoTek Страницы: 4

Master View CS-172

Бренд: ATEN Страницы: 1

Бренд: Wyrestorm Страницы: 4

Magnum Quad-Series

Бренд: GarrettCom Страницы: 55

Бренд: Datavideo Страницы: 72

950-2080 NEW STYLE GAS PRESSURE SWITCH

Бренд: TJERNLUND Страницы: 1

CoreBuilder 7000

Бренд: 3Com Страницы: 516

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды