Cisco Nexus 9396PX Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 74

background image

Switch Power Input Requirements

The following table lists the typical amount of power that the switch consumes. It also lists the maximum
amount of power that you must provision for the switch and power supply for peak conditions.

Some power supplies have UL listed capabilities that are greater than the maximum power requirements for
a switch. To determine the power consumption characteristics for the switch, use the typical and maximum
requirements that are listed in the following table.

Note

Heat Dissipation
Requirement

Maximum Power
Consumption (AC or DC)

Typical Power
Consumption (AC or DC)

Switch

1552.524 BTUs per hour

455 W

232 W

Cisco Nexus 9396PX

Power Specifications

Power specifications include the specifications for each type of power supply module.

650-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• N9K-PAC-650W

• N9K-PAC-650W-B

Specification

Characteristic

Nominal range: 100 and 240 VAC (Range: 90-132
VAC, 180-264 VAC)

AC input voltage

Nominal range: 50 to 60 Hz (Range: 47-63 Hz)

AC input frequency

7.6 A at 100 VAC

3.65 A at 208 VAC

Maximum AC input current

760 A at 100 VAC

Maximum input volt-amperes

650 W

Maximum output power per power supply

33 A (sub-cycle duration)

Maximum inrush current

12 ms at 650 W

Maximum hold-up time

12 VDC

Power supply output voltage

12 VDC

Power supply standby voltage

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

49

System Specifications

Switch Power Input Requirements

«
...
57
58
59
60
61
...
»

Содержание Nexus 9396PX











































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 9396PX

Бренд: Qlogic Страницы: 4

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

Бренд: HPM Страницы: 4

Бренд: Yamamoto Electric Works Co., Ltd. Страницы: 15

Бренд: Micrel Страницы: 15

Бренд: Alloy Страницы: 33

Бренд: Guntermann & Drunck Страницы: 20

Бренд: ATEN Страницы: 21

Бренд: Gefen Страницы: 9

PowerGATE LELTS-1 Series

Бренд: Lex Страницы: 12

IP-Watcher 2x2 Digital PoE

Бренд: W&T Страницы: 79

Intraplex T1 DCS-9530 CrossConnect System

Бренд: GatesAir Страницы: 106

Бренд: UNICOM Страницы: 8

Бренд: Avatar Technologies Страницы: 9

System Sensor EPS40 Series

Бренд: Pittway Страницы: 4

Бренд: Zenith Страницы: 22

Zenith ZTG Series

Бренд: ABB Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды