manualshive.com logo in svg

Cisco ASR 9000 Series, Справочник по командам

Поделиться
Скачать
Cisco ASR 9000 Series Скачать руководство пользователя страница 474

frame-relay multilink hello

To configure the hello interval used by a Frame Relay multilink bundle link, use the

frame-relay multilink

hello

command in interface configuration mode. To reset the name to the default, use the

no

form of this

command.

frame-relay multilink hello hello-interval

no frame-relay multilink hello

Syntax Description

Hello interval for the Frame Relay multilink bundle link, in seconds. The
range is from 1 to 180.

hello-interval

Command Default

The default hello interval is 10 seconds.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

frame-relay multilink hello

command is supported only on serial interfaces. The

frame-relay

multilink hello

command is not supported on Packet-over-SONET/SDH (POS) or multilink frame relay

interfaces.

Note

The

frame-relay multilink hello

command can be configured only on bundle link interfaces that have been

associated with a bundle using the

encapsulation frame-relay mfr

command.

You can enter the

frame-relay multilink hello

command at any time without affecting the current state

of the interface; however, the configured hello interval value does not go into effect until the interface has
gone from the down state to the up state. One way to bring the interface down and back up again is by
using the

shutdown

and

no shutdown

commands in interface configuration mode.

Note

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

454

Frame Relay Commands on the Cisco ASR 9000 Series Router

frame-relay multilink hello

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды