Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 22

Страница: 22 / 302

Chapter 1 An Overview of the Cisco Unified IP Phone

Understanding the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE

1-4

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

The following table describes the buttons on the Cisco Unified IP Phones
7961G/7961G-GE and 7941G/7941G-GE:

Programmable
buttons

Depending on configuration, programmable buttons provide access to:

•

Phone lines (line buttons)

•

Speed-dial numbers (speed-dial buttons, including the BLF speed-dial
feature)

•

Web-based services (for example, a Personal Address Book (PAB)
button)

•

Phone features (for example, a Privacy button)

The buttons illuminate to indicate status:

Green, steady—Active call

Green, flashing—Held call

Amber, steady—Privacy in use

Amber, flashing—Incoming call

Red steady—Remote line in use (shared line, BLF status, or active
Mobile Connect call)

Phone screen

Shows phone features.

Footstand button

Allows you to adjust the angle of the phone base.

Messages button

Auto-dials your voice message service (varies by service).

Directories button

Opens/closes the Directories menu. Use it to access call logs and directories.

Help button

Activates the Help menu.

Settings button

Opens/closes the Settings menu. Use it to control phone screen contrast and
ring sounds.

Services button

Opens/closes the Services menu.

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Результаты поиска

Содержание 7941G - Unified IP Phone VoIP

Отзывы:

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренды по названию

Популярные бренды

Cisco 7941G - Unified IP Phone VoIP, Руководство администратора

Результаты поиска

Содержание 7941G - Unified IP Phone VoIP

Отзывы:

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренды по названию

Популярные бренды