Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 197

Страница: 197 / 302

7-7

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

Chapter 7 Viewing Model Information, Status, and Statistics on the Cisco Unified IP Phone

Status Menu

DNS timeout

DNS server did not respond.

•

Network is busy—The errors should
resolve themselves when the network
load reduces.

•

No network connectivity between the
DNS server and the phone—Verify the
network connections.

•

DNS server is down—Check
configuration of DNS server.

DNS unknown host

DNS could not resolve the
name of the TFTP server or
Cisco Unified
Communications Manager.

•

Verify that the host names of the TFTP
server or Cisco Unified Communications
Manager are configured properly in DNS.

•

Consider using IP addresses rather than
host names.

Duplicate IP

Another device is using the IP
address assigned to the phone.

•

If the phone has a static IP address, verify
that you have not assigned a duplicate IP
address. See the

“Network Configuration

Menu” section on page 4-7

section for

details.

•

If you are using DHCP, check the DHCP
server configuration.

Table 7-2

Status Messages on the Cisco Unified IP Phone (continued)

Message

Description

Possible Explanation and Action

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Результаты поиска

Содержание 7941G - Unified IP Phone VoIP

Отзывы:

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренды по названию

Популярные бренды

Cisco 7941G - Unified IP Phone VoIP, Руководство администратора

Результаты поиска

Содержание 7941G - Unified IP Phone VoIP

Отзывы:

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренды по названию

Популярные бренды