Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 237 | Manualshive

Страница: 237 / 302

background image

9-9

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

Chapter 9 Troubleshooting and Maintenance

Cisco Unified IP Phone Resets Unexpectedly

•

Identifying Intermittent Network Outages, page 9-9

•

Verifying DHCP Settings, page 9-9

•

Checking Static IP Address Settings, page 9-10

•

Verifying the Voice VLAN Configuration, page 9-10

•

Verifying that the Phones Have Not Been Intentionally Reset, page 9-10

•

Eliminating DNS or Other Connectivity Errors, page 9-11

Verifying the Physical Connection

Verify that the Ethernet connection to which the Cisco Unified IP Phone is
connected is up. For example, check whether the particular port or switch to
which the phone is connected is down and that the switch is not rebooting. Also
make sure that there are no cable breaks.

Identifying Intermittent Network Outages

Intermittent network outages affect data and voice traffic differently. Your
network might have been experiencing intermittent outages without detection. If
so, data traffic can resend lost packets and verify that packets are received and
transmitted. However, voice traffic cannot recapture lost packets. Rather than
retransmitting a lost network connection, the phone resets and attempts to
reconnect its network connection.

If you are experiencing problems with the voice network, you should investigate
whether an existing problem is simply being exposed.

Verifying DHCP Settings

The following suggestions can help you determine if the phone has been properly
configured to use DHCP:

1.

Verify that you have properly configured the phone to use DHCP. See the

“Network Configuration Menu” section on page 4-7

for more information.

2.

Verify that the DHCP server has been set up properly.

3.

Verify the DHCP lease duration. Cisco recommends that you set it to 8 days.

«
...
235
236
237
238
239
...
»

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренд: 8*8 Страницы: 5

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 4

Бренд: Aastra Страницы: 2

Бренд: Eaton Страницы: 44

Бренд: Samsung Страницы: 50

Бренд: Samsung Страницы: 37

Бренд: Samsung Страницы: 95

Бренд: Samsung Страницы: 131

Бренд: Samsung Страницы: 153

Бренд: Samsung Страницы: 155

Бренд: Samsung Страницы: 189

R225 - SGH Cell Phone

Бренд: Samsung Страницы: 65

Бренд: Samsung Страницы: 118

Бренд: Samsung Страницы: 38

Бренд: G53 Limited Страницы: 10

Бренд: ATCOM Страницы: 9

Бренд: RATH MICROTECH Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды