Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 302

background image

Chapter 4 Configuring Settings on the Cisco Unified IP Phone

Device Configuration Menu

4-18

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

•

Line Settings Menu, page 4-20

SIP General Configuration Menu

The SIP General Configuration menu displays information about the configurable
SIP parameters on the phone.

Table 4-3

describes the options in this menu.

Table 4-3

SIP General Configuration Menu Options

Option

Description

To Change

Preferred CODEC

Displays the CODEC to use when a call is
initiated. This value will always be set to
none.

Display only—cannot configure.

Out of Band DTMF

Displays the configuration of the
out-of-band signaling (for tone detection on
the IP side of a gateway). The Cisco Unified
IP phone (SIP) supports out-of-band
signaling by using the AVT tone method.
This value will always be set to avt.

Display only—cannot configure.

Register with Proxy

Displays if the phone must register with a
proxy server during initialization. This value
will always be set to true.

Display only—cannot configure.

Register Expires

Displays the amount of time, in seconds,
after which a registration request expires.

From Cisco Unified
Communications Manager
Administration,

Device > Device

Settings >

SIP Profile

.

Phone Label

Displays the text that is displayed on the top
right status line of the LCD on the phone.
This text is for end-user display only and has
no effect on caller identification or
messaging. This value will always be set to
null.

Display only—cannot configure.

Enable VAD

Displays if voice activation detection (VAD)
is enabled.

From Cisco Unified
Communications Manager
Administration,

Device > Device

Settings > SIP Profile

.

«
...
112
113
114
115
116
...
»

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренд: Safeline Страницы: 32

Бренд: Krüger & Matz Страницы: 20

Бренд: Alcatel Страницы: 51

Бренд: Allview Страницы: 142

Бренд: TCL Страницы: 74

Бренд: Snom Страницы: 2

Бренд: Docomo Страницы: 194

Бренд: Mitel Страницы: 60

StrongPhone WiFi

Бренд: Evolveo Страницы: 9

OPENTOUCH ALE-300

Бренд: Alcatel-Lucent Страницы: 101

Бренд: DDM Brands Страницы: 74

Бренд: AMGOO Страницы: 32

Бренд: Telme Страницы: 102

Бренд: Dukane Страницы: 148

Бренд: Zte Страницы: 91

X-Treme PQ 68 Netphone

Бренд: Sigma Страницы: 34

Galaxy Express Prime

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды