Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 302

background image

9-21

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

Chapter 9 Troubleshooting and Maintenance

Using the Quality Report Tool

Using the Quality Report Tool

The Quality Report Tool (QRT) is a voice quality and general problem-reporting
tool for the Cisco Unified IP Phone. The QRT feature is installed as part of the
Cisco Unified Communications Manager installation.

You can configure users’ Cisco Unified IP Phones with QRT. When you do so,
users can report problems with phone calls by pressing the QRT softkey. This
softkey is available only when the Cisco Unified IP Phone is in the Connected,
Connected Conference, Connected Transfer, and/or OnHook states.

When a user presses the

QRT

softkey, a list of problem categories appears. The

user selects the appropriate problem category, and this feedback is logged in an
XML file. Actual information logged depends on the user selection, and whether
the destination device is a Cisco Unified IP Phone.

For more information about using QRT, refer to

Cisco Unified Communications

Manager Serviceability Administration Guide

,

Cisco Unified Communications

Manager Serviceability System Guide,

and

Cicso Communications Manager

Features and Services Guide

.

Monitoring the Voice Quality of Calls

To measure the voice quality of calls that are sent and received within the network,
Cisco Unified IP Phones use these statistical metrics that are based on
concealment events. The DSP plays concealment frames to mask frame loss in the
voice packet stream.

•

Concealment Ratio metrics—Show the ratio of concealment frames over total
speech frames. An interval conceal ratio is calculated every 3 seconds.

•

Concealed Second metrics—Show the number of seconds in which the DSP
plays concealment frames due to lost frames. A severely “concealed second”
is a second in which the DSP plays more than five percent concealment
frames.

•

MOS-LQK metrics—Use a numeric score to estimate the relative voice
listening quality. The Cisco Unified IP Phone calculates the mean opinion
score (MOS) for listening quality (LQK) based audible concealment events
due to frame loss in the preceding 8 seconds, and includes perceptual
weighting factors such as codec type and frame size.

«
...
247
248
249
250
251
...
»

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренд: TCL Страницы: 27

Бренд: Palm Страницы: 28

700wx - Treo Smartphone 60 MB

Бренд: Palm Страницы: 2

700wx - Treo Smartphone 60 MB

Бренд: Palm Страницы: 30

700w - Treo Smartphone 60 MB

Бренд: Palm Страницы: 14

9520 - Charging Pod For

Бренд: Blackberry Страницы: 2

Бренд: Rath Страницы: 9

Бренд: Hammer Страницы: 11

Aastra 480i SIP

Бренд: ADTRAN Страницы: 29

Бренд: SAIET Страницы: 49

Бренд: T-Mobile Страницы: 43

DROID DROID INCREDIBLE

Бренд: HTC Страницы: 206

Бренд: VERTIS Страницы: 23

STUDIO ENERGY 2

Бренд: Blu Страницы: 20

Бренд: Cellacom Страницы: 22

Бренд: NGM Страницы: 148

Transform SPH-M920

Бренд: Samsung Страницы: 238

Бренд: Samsung Страницы: 203

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды