Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 302

background image

7-5

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

Chapter 7 Viewing Model Information, Status, and Statistics on the Cisco Unified IP Phone

Status Menu

Table 7-2

Status Messages on the Cisco Unified IP Phone

Message

Description

Possible Explanation and Action

BootP server used

The phone obtained its IP
address from a BootP server
rather than a DHCP server.

None. This message is informational only.

CFG file not found

The name-based and default
configuration file was not
found on the TFTP Server.

The configuration file for a phone is created
when the phone is added to the Cisco
Unified Communications Manager database.
If the phone has not been added to the Cisco
Unified Communications Manager database,
the TFTP server generates a

CFG File Not

Found

response.

•

Phone is not registered with Cisco
Unified Communications Manager.

You must manually add the phone to
Cisco Unified Communications Manager
if you are not allowing phones to
auto-register. See the

“Adding Phones

with Cisco Unified Communications
Manager Administration” section on
page 2-17

for details.

•

If you are using DHCP, verify that the
DHCP server is pointing to the correct
TFTP server.

•

If you are using static IP addresses, check
configuration of the TFTP server. See the

“Network Configuration Menu” section
on page 4-7

for details on assigning a

TFTP server.

CFG TFTP Size Error The configuration file is too

large for file system on the
phone.

Power cycle the phone.

«
...
193
194
195
196
197
...
»

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренд: Xblue Networks Страницы: 98

ONETOUCH POP 7S P330X

Бренд: Alcatel Страницы: 32

Бренд: Alcatel Страницы: 51

ONE TOUCH Fierce

Бренд: Alcatel Страницы: 15

Бренд: Docomo Страницы: 194

Бренд: Mitel Страницы: 60

Бренд: Spice Страницы: 26

Бренд: Pacific GSM Страницы: 8

Бренд: T-Mobile Страницы: 212

Бренд: Allview Страницы: 88

Бренд: iBall Страницы: 150

Бренд: Palm Страницы: 54

Бренд: switel Страницы: 4

Бренд: Lava Страницы: 21

Бренд: Lenovo Страницы: 33

Бренд: Lenovo Страницы: 21

Бренд: Lenovo Страницы: 74

Бренд: Lenovo Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды