Cisco 7941G - Unified IP Phone VoIP Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 302

background image

Chapter 3 Setting Up the Cisco Unified IP Phone

Understanding the Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE Components

3-4

Cisco Unified IP Phone 7961G/7961G-GE and 7941G/7941G-GE for Cisco Unified Communications Manager 6.1

OL-14620-01

–

labeled 10/100/1000 SW on the 7961G-GE and 7941G-GE

•

Access port

–

labeled 10/100 PC on the 7961G and 7941G

–

labeled 10/100/1000 PC on the 7961G-GE and 7941G-GE

Each port supports 10/100 Mbps or 10/100/1000 half- or full-duplex connections
to external devices. You can use either Category 3 or 5 cabling for 10 Mbps
connections, but you must use Category 5 for 100 and 1000 Mbps connections.

Use the SW network port to connect the phone to the network. You must use a
straight-through cable on these ports. The phone can also obtain inline power
from a switch over these connections. See the

“Adding Phones to the Cisco

Unified Communications Manager Database” section on page 2-14

for details.

Use the PC access port to connect a network device, such as a computer, to the
phone. You must use a straight-through cable on this port.

Handset

The handset is designed especially for use with a Cisco Unified IP Phone. It
includes a light strip that indicates incoming calls and voice messages waiting.

To connect a handset to the Cisco Unified IP Phone, remove the hookswitch clip
(see illustration below) from the cradle area. Then plug the cable into the handset
and into the Handset port on the back of the phone.

Figure 3-1

Removing the Hookswitch Clip

185165

«
...
78
79
80
81
82
...
»

Содержание 7941G - Unified IP Phone VoIP















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7941G - Unified IP Phone VoIP

Бренд: Pantech Страницы: 54

Бренд: HTC Страницы: 16

Бренд: EASY3CALL Страницы: 40

Бренд: Avaya Страницы: 237

Бренд: Proolin VoIP Tech Страницы: 25

Бренд: Doro Страницы: 68

Бренд: ZTE-G Страницы: 33

Бренд: Grandstream Networks Страницы: 19

Бренд: Samsung Страницы: 144

Бренд: Samsung Страницы: 160

Бренд: Samsung Страницы: 162

Бренд: Samsung Страницы: 186

Бренд: Samsung Страницы: 144

Бренд: Samsung Страницы: 195

Бренд: Samsung Страницы: 195

Бренд: Samsung Страницы: 7

Бренд: Sedna Страницы: 8

MultiPhone PAP4505DUO

Бренд: Prestigio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды