![background image](http://html.mh-extra.com/html/cisco/2800-series/2800-series_manual_64812171.webp)
Hoot and Holler over V3PN Configuration Example
Verify
31
OL-6573-01
in use settings ={Tunnel, }
slot: 0, conn id: 5152, flow_id: 32, crypto map: INT_CM
crypto engine type: Hardware, engine_id: 2
sa timing: remaining key lifetime (k/sec): (508938172/10695)
ike_cookies: 795753FB 41D07F6D DE2C7D5A FB6197B3
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
The following is an output example for the
show ip ospf neighbor
command, performed using the
configuration on the Branch 1 router:
Branch-1#
show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
192.168.1.1 0
FULL
/ - 00:00:35 192.168.1.1
Tunnel0
The following is an output example from the
show ip route
command, performed using the
configuration on the Branch 1 router:
Branch-1#
show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 10.32.153.33 to network 0.0.0.0
192.168.4.0/32 is subnetted, 1 subnets
O 192.168.4.1 [110/11] via 192.168.1.1, 00:33:28, Tunnel0
O 192.168.5.0/24 [110/21] via 192.168.1.1, 00:33:28, Tunnel0
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
C 10.32.153.33/32 is directly connected, Virtual-Access4
C 10.32.153.32/30 is directly connected, Virtual-Access3
is directly connected, Virtual-Access4
O 192.168.6.0/24 [110/11] via 192.168.1.1, 00:33:28, Tunnel0
C 192.168.7.0/24 is directly connected, Vif1
O 192.168.1.0/24 [110/11] via 192.168.1.1, 00:33:28, Tunnel0
C 192.168.2.0/24 is directly connected, FastEthernet0/0
O 192.168.3.0/24 [110/21] via 192.168.1.1, 00:33:28, Tunnel0
S* 0.0.0.0/0 [1/0] via 10.32.153.33
The following is an output example for the
show ip pim neighbor
command, performed using the
configuration on the Branch 1 router:
Branch-1#
show ip pim neighbor
PIM Neighbor Table
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
192.168.1.1 Tunnel0 00:20:59/00:01:25 v2 1 / S
The following is an output example for the
show ip pim rp mapping
command, performed using the
configuration on the Branch 1 router:
Branch-1#
show ip pim rp mapping
Содержание 2800 Series
Страница 64: ...22 Basic Software Configuration Using the Cisco IOS Command Line Interface OL 5593 01 Additional References ...
Страница 125: ...Easy VPN Configuration Example Configure 5 OL 6340 01 Private IP address pool 192 168 3 0 24 ...
Страница 138: ...Easy VPN Configuration Example Related Information 18 OL 6340 01 ...
Страница 140: ...Easy VPN Configuration Example Related Information 20 OL 6340 01 ...