Cincinnati Sub-Zero HEMOTHERM 400CE, Руководство по эксплуатации, Страница: 78 / 95

OPERATION MANUAL HEMOTHERM MODEL 400CE
Page 31 of 46
EMC COMPATIBILITY TABLES ACCORDING TO IEC 60601-1-2
Guidance and manufacturer’s declaration – electromagnetic emissions
The Hemotherm, Model 400CE is intended for use in the electromagnetic environment specified below. The customer or the user of
this unit should assure that it is used in such an environment.
Emissions tests Compliance Electromagnetic environment
– guidance
RF emissions
CISPR 11
Group 1
The Hemotherm, Model 400CE uses RF energy only for its internal
function. Therefore, its RF emissions are very low and are not
likely to cause any interference in nearby electronic equipment.
RF emissions
CISPR 11
Class A
The Hemotherm, Model 400CE is suitable for use in all
establishments other than domestic and those directly connected to
the public low-voltage power supply network that supplies buildings
used for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies
Guidance and manufacturer’s declaration – electromagnetic immunity
The Hemotherm, Model 400CE is intended for use in the electromagnetic environment specified below. The customer or the user of the
Hemotherm, Model 400CE should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2 ±6 kV contact
±8 kV air ±6 kV contact
±8 kV air Floors should be wood, concrete or ceramic tile. If floors
are covered with synthetic material, the relative humidity
should be at least 30%.
Electrical fast
transient/burst
IEC 61000-4-4 ±2 kV for power supply
lines
±1 kV for input/output
lines ±2 kV for power
supply lines
±1 kV for input/output
lines Mains power quality should be that of a typical
commercial or hospital environment.
Surge
IEC 61000-4-5 ±1 kV differential mode
±2 kV common mode ±1 kV differential
mode
±2 kV common mode Mains power quality should be that of a typical
commercial or hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC 61000-4-11
<5%
U
T
(>95% dip in
U
T
)
for 0,5 cycle
40%
U
T
(60% dip in
U
T
)
for 5 cycles
70%
U
T
(30% dip in U
T
)
for 25 cycles
<5%
U
T
(>95% dip in
U
T
)
for 5 s
<5%
U
T
(>95% dip in
U
T
)
for 0.5 cycle
40%
U
T
(60% dip in
U
T
)
for 5 cycles
70%
U
T
(30% dip in U
T
)
for 25 cycles
<5%
U
T
(>95% dip in
U
T
)
for 5 s
Mains power quality should be that of a typical
commercial or hospital environment. If the user of the
Hemotherm, Model 400CE requires continued operation
during power mains interruptions, it is recommended that
the Hemotherm, Model 400CE be powered from an
uninterruptible power supply or a battery.
Power frequency
(50/60 Hz) magnetic
field
IEC 61000-4-8 3 A/m 3 A/m Power frequency magnetic fields should be at levels
characteristic of a typical location in a typical commercial
or hospital environment.
Note: U
T
is the a. c. mains voltage prior to application of the test level.