Cichewicz MOC 20 Скачать руководство пользователя страница 12

12 

 

12/03/12 

Maintenance photocell. 
If the reading lights on the controller starts to drop it, disconnect the electrical plug burner, remove 
the cover of the burner, remove the Photo element of the sleeve and clean the surface with a dry soft 
cloth.  This  action  is  performed  at  least  once  during  the  1-2  heating  season,  or  more  frequently  if 
necessary. 
Cleaning the air duct burner. 
To do this: 
• Remove the burner or open the door of the burner. 
• Remove the heat shield and sealing of the furnace grate. 
• Remove and clean the cast iron grate blowing holes in the surface 
• Remove ashes from the air duct under the grate and clean the vents holes on the back burner 
chamber around the internal screw (Stoker). 
• Reinstall the grate, burner plate and seal. 
Cleaning the burner must be made with a disconnected electrical connector from the burner at least 
1-2 times during the heating season, or more frequently if necessary. 
 
Cleaning the fan. 
Before each heating season, remove the burner and fan with a brush or compressed air to clear the 
shoulders of pollution. 
 
 
Replacing the igniter. 
Electric  igniter  is  used  to  fire  the  pellet  is  a  consumable  item,  and  its  lifetime  depends  on  the 
number ignitions, their duration, power fan with ignition or correct adjustment. The life expectancy 
is one to three heating seasons. If damaged replace it. 
To do this: 
• Disconnect the electrical connector and disassemble the burner housing. 
• Disconnect heater wires from the electrical connector (see wiring diagram) 
• disassemble the internal screw drive and the back cover of the burner. 
• In the auger tube is mounted ignition (heat). Is screwed to the side of the set crew, which unscrew 
and remove the lighter. 
• Install a new nut and tighten the screw. 
• Connect the wires to the electrical connector lighter burner. 
• Mount the enclosure and drive. 
 
Elements of performance. 
Torch  building  elements  such  as  ignition,  cast  iron  grate,  burner  heat  shield,  gasket,  sealing  cords 
are consumable and they have only guarantee the boot. They should be replaced as wear every 1-3 
heating seasons. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MOC 20
















Отзывы: