Chroma 63200A Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 141

background image

iii

Warranty

All of Chroma’s instruments are warranted against defects in material and workmanship for a
period of one year from date of shipment. Chroma agrees to repair or replace any assembly
or component found to be defective, und

er normal use during this period. Chroma’s

obligation under this warranty is limited solely to repairing any such instrument, which in
Chroma’s sole opinion proves to be defective within the scope of the warranty when returned
to the factory or to an authorized service center.  Purchaser is responsible for the shipping
and cost of the service item to Chroma factory or service center.  Shipment should not be
made without prior authorization by Chroma.

This warranty does not apply to any products repaired or altered by persons not authorized
by Chroma, or not in accordance with instructions furnished by Chroma.  If the instrument is
defective as a result of misuse, improper repair, or abnormal conditions or operations,
repairs will be billed at cost.

Chroma assumes no responsibility for its product being used in a hazardous or dangerous
manner either alone or in conjunction with other equipment.  High voltage used in some
instruments may be dangerous if misused.  Special disclaimers apply to these instruments.
Chroma assumes no liability for secondary charges or consequential damages and in any
event, Chroma’s liability for breach of warranty under any contract or otherwise, shall not
exceed the purchase price of the specific instrument shipped and against which a claim is
made.

Any recommendations made by Chroma regarding the use of its products are based upon
tests believed to be reliable; Chroma makes no warranty of the results to be obtained.  This
warranty is in lieu of all other warranties, expressed or implied, and no representative or
person is authorized to represent or assume for Chroma any liability in connection with the
sale of our products other than set forth herein.

CHROMA ATE INC.

66 Huaya 1st Road, Guishan,
Taoyuan 33383, Taiwan
Tel: 886-3-327-9999
Fax: 886-3-327-2886
e-mail:

[email protected]

http://www.chromaate.com

«
...
2
3
4
5
6
...
»

Содержание 63200A Series














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 63200A Series

Бренд: ABB Страницы: 86

Бренд: iGuzzini Страницы: 20

Бренд: Panasonic Страницы: 174

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Land Pride Страницы: 36

Skid Steer Rakes SR2672

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 2

Disc Harrows DH3510

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 4

Бренд: Land Pride Страницы: 4

Straw Crimper CR2572

Бренд: Land Pride Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды