Christini AWD 250 Скачать руководство пользователя страница 76

Страница: 76 / 124

Page 75

•

Insert set screw with light dab of blue Loctite. When set screw is
fully seated, it will be slightly below the surface of driveshaft. If
not, make sure that spline shaft is fully seated on pinion gear.

•

Grease pinion gear and bevel gear with Shell Lithium grease.

•

Insert cover/bevel gear assembly onto dropout.

•

Insert 6 cover bolts and tighten in a cross star pattern using a
4mm Allen wrench. Tighten to 8ft-lbs.

•

Check that drive carrier spins freely and wipe excess grease from
outside of dropout.

•

Reinsert bellow and bellow clamp over spline shaft and crimp
bellow down using crimping tool or vise grips.

WARNING:

WARNING: The band of clamp must be over the set screw to ensure
that the set screw can not back out.

•

Lightly grease spline shaft with Shell Lithium grease.

•

Reinsert forks into triple clamps.

Dropout Service

Содержание AWD 250





























































































































Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды

Christini AWD 250, Руководство по обслуживанию

Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды