Christini AWD 250 Скачать руководство пользователя страница 120

Страница: 120 / 124

Page 119

Front forks feel sticky

•

Clean and lube fork seals.

•

Check to make sure forks are not twisted in triple
clamps.

•

Lube front spline shafts with grease.

•

If this does not help, pull down dust boot and check
spline shaft for damage.

•

Disassemble spline and check bearing for corrosion and
damage.

•

Make sure front wheel axle bolt is not too tight and is not
binding forks

Front wheel is not pulling

•

Make sure engagement switch is turned on and the en-
gagement spline is functioning properly.

•

Check clutch setting for proper torque using “wheel
check method”.

Drive system is pulling to one side

•

Perform “Sprag bearing test” as described in manual

•

Check sprag bearings in hub to make sure neither side is
slipping.

•

Make sure that drive shafts are free to spin smoothly.
Occasionally mud or other debris can hinder one drive-
shaft from spinning at the proper rate.

Clutch Basket has notches in it.

•

This is normal. As long as the notches don’t exceed
3/16”, Replacement is not needed.

Cannot disengage system

•

With bike in neutral rock it back and forth and use the
lever to disengage the system.

•

Engagement cable has too much slack in it. Use barrel
adjuster to take slack out of cable.

AWD Troubleshooting

Problem

Solution

Содержание AWD 250





























































































































Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды

Christini AWD 250, Руководство по обслуживанию

Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды