Christini AWD 250 Скачать руководство пользователя страница 73

Страница: 73 / 124

Page 72

•

Install cover bearing into cover with bearing installation tools.

•

Install internal and external cover 0-rings. Note:

Note:

Note: all 0-rings should

be lightly coated with grease before being reassembled.

•

Insert drive carrier o-ring on drive carrier and insert drive carrier

into cover and tap into place. Note:

Note:

Note: face of drive carrier should be

flush with cover bearing and machined cover surface.

•

Place drive insert on tooth side of bevel gear and line up all four
threaded holes with clearance holes on gear.

•

Set cover and drive carrier on top of bevel gear assembly, with
smooth side of gear facing the cover. Line up 4 bolt holes and

thread drive carrier bolts into drive insert.  Blue Loctite should be
used on bolts.  Final tightening of bolts will require a square bar or
soft jaws to keep gear from spinning.  Torque bolts to 8ft ft-lbs.

•

Check that bevel gear spins freely on cover. If it does not spin
freely, check to make sure all o-rings and the cover bearing are

properly seated. If new o-rings are used, there may be more
friction until o-rings seat and break in.

•

Insert axle o-ring into drive carrier.

Dropout Service

Содержание AWD 250





























































































































Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды

Christini AWD 250, Руководство по обслуживанию

Результаты поиска

Содержание AWD 250

Отзывы:

Похожие инструкции для AWD 250

Бренды по названию

Популярные бренды