Christini AWD 250 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 124

background image

Page 45

AWD Clutch Test

•

Place the bike on a stand and make sure that the front wheel
is not touching the ground.

•

Shift the bike into gear.

•

Turn the AWD switch to the on position and check to make
sure the AWD is engaged.

•

Grab the front wheel with two hands and try to spin it back-
wards.  The front wheel should spin backwards but require a
large amount of effort to do so.  If the wheel will not break
free, the clutch is set too high.  If the wheel turns backwards
very easily, the clutch is set too low.

•

If the clutch needs to be adjusted, pull the gas tank off the
bike.

•

Loosen the set screw on the clutch locknut.

•

Turn the locknut in or out a 1/2 turn at a time until the front
wheel moves backward with the correct amount of force. To
keep driveshaft from spinning apply front brake.

•

Make sure the set screw is positioned over a flat in the clutch
hub and tighten the set screw down and reinstall the tank.

«
...
44
45
46
47
48
...
»

Содержание AWD 250





























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 250

Бренд: R&G Страницы: 4

Бренд: KTM Страницы: 13

KTM 1190 LED Light Bar

Бренд: CYCLOPS Страницы: 4

Dirt Runner 90cc

Бренд: Baja motorsports Страницы: 66

Бренд: R&G Страницы: 24

Бренд: Fantic Motor Страницы: 145

Бренд: KTM Страницы: 38

Бренд: kellermann Страницы: 2

Бренд: BMW Страницы: 139

KODIAK YFM70KDXM

Бренд: Yamaha Страницы: 180

Бренд: Yamaha Страницы: 156

RAPTOR 700R 2022

Бренд: Yamaha Страницы: 160

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: ACERBIS Страницы: 72

Бренд: Kinderkraft Страницы: 36

Бренд: Datatool Страницы: 5

Бренд: Datatool Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды