Christini AWD 250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 124

background image

Page 13

This motorcycle uses a capacitor discharge ignition system
(CDI). The ignition system should never require adjustment
unless the stator of the magnetic flywheel was incorrectly
installed during engine reassembly. If necessary, inspect
and adjust as follows:

Adjustment

Adjustment

Adjustment

Adjustment
- Remove the magnetic flywheel cover.
- Make sure that the mark on the stator plate is aligned with
the mark on the crankcase.
- If the marks are not aligned, loosen the magnetic inertia
wheel screws and turn it.
- Tighten the screws securely.
- Install the magnetic flywheel cover.

NOTE

NOTE

NOTE

NOTE

Engine tune-up can be adjusted to match the rider´s preferences and skills.

- Remove the magnetic flywheel cover.
- Loosen the stator screws.
- Adjust the engine tune-up by changing the position of the stator within prudent limits

NOTE

NOTE

NOTE

NOTE

For the best engine performance, it is very important to adjust the engine tune-up within the set of limits
described.

- Tighten the stator screws.
- Install the magnetic flywheel cover.
- Test ride the motorcycle and readjust the engine tune-up, if necessary.

Electronic Ignition

«
...
12
13
14
15
16
...
»

Содержание AWD 250





























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 250

Бренд: ZARD Страницы: 2

Бренд: Kabuto Страницы: 40

Бренд: hepco & becker Страницы: 2

Бренд: GAS GAS Страницы: 34

Бренд: B-PWR Страницы: 13

Бренд: LAZER Страницы: 19

Бренд: Kong Страницы: 72

Turismo Veloce 800 LUSSO

Бренд: AGUSTA Страницы: 616

Бренд: Yoshimura Страницы: 4

Бренд: Kabuto Страницы: 19

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды