Christini AWD 250 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 124

background image

Page 21

THROTLE CABLE

THROTLE CABLE

THROTLE CABLE

THROTLE CABLE
-  Check that the throttle grip turns smoothly.
-  Check that the throttle grip has 2-3 mm of free play.
-  If the free play is incorrect, loosen the locknut on the
upper end of the throttle cable, and turn the adjuster to
obtain the correct amount of free play.
- Tighten the locknut again.
-  If the free play cannot be set by adjusting the cable, re-
move the cable protector in the throttle body. Make the
necessary free play adjustments with the tensor at the
end of the cable, tighten the locknut, and reinstall the
protector.

CARBURETOR

CARBURETOR

CARBURETOR

CARBURETOR
Idle speed adjustment

Idle speed adjustment

Idle speed adjustment

Idle speed adjustment
Is carried out using the air screw (A) and idle screw (B).
-  First turn in the air screw until it is loose, then tighten it
1 1/2 turns.
-  After thoroughly warming up the engine, turn the idle
adjusting screw to obtain the desired idle speed. If there
are no idle preferences, turn the screw until the engine
stops.
-  Tighten lightly the idle screw.
-  Open and close the throttle a few times to make sure the idle speed does not change. Readjust if neces-
sary.
-  With the engine idling, turn the handlebar to each side. If handlebar movement changes the idle speed,
the throttle cable may be improperly adjusted or routed incorrectly, or it may be damaged.  Be sure to cor-
rect any of these conditions before riding.

WARNING

WARNING

WARNING

WARNING

Riding with a damaged throttle cable could be dangerous.

Throttle/Carburetor

«
...
20
21
22
23
24
...
»

Содержание AWD 250





























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 250

Avenger 150 Street

Бренд: Bajaj Auto Страницы: 40

Бренд: Yamaha Страницы: 287

Rebellion Electric Chopper 15130760

Бренд: Razor Страницы: 17

Бренд: R&G Страницы: 9

Бренд: KSR Moto Страницы: 51

Бренд: TRS Страницы: 38

Бренд: kellermann Страницы: 7

Бренд: Yoshimura Страницы: 4

Бренд: rizoma Страницы: 16

RACE 11621C0520

Бренд: Yoshimura Страницы: 7

Бренд: Yamaha Страницы: 104

Super Tenere ABS 2018

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 97

Бренд: Baja motorsports Страницы: 20

Бренд: Honda Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: Arai Helmet Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды