Christini AWD 250 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 124

background image

Page 27

WHEELS

WHEELS

WHEELS

WHEELS

Tires

Tires

Tires

Tires
- Tire pressure affects traction, and tire life.
- Adjust the tire pressure to match road conditions and rider’s preference, but do not stray too far from the
recommended pressure.

NOTE

NOTE

NOTE

NOTE

Tire pressure should be checked when the tires are cold before riding.

Road conditions

Road conditions

Road conditions

Road conditions
- When the road is wet, muddy, sandy or slippery, reduce the tire pressure.
- On gravel roads or hard terrain, increase the tire pressure.

Spokes and wheel rims

Spokes and wheel rims

Spokes and wheel rims

Spokes and wheel rims
The spokes on both wheels must be tightened evenly and should not be allowed to have free play. Unevenly
tightened or loose spokes will cause wheel rim run out, the other spokes will be stressed and might break.

Wheel rim run out

Wheel rim run out

Wheel rim run out

Wheel rim run out
Place a dial indicator at the rim side, and spin
the wheel by hand to measure the axial run out.
Place the dial indicator at the inner circumfer-
ence of the wheel and spin the wheel, the differ-
ence between the highest and lowest quantities
is the run out.  If the run out is not excessive it
can be corrected tightening or loosening some
spokes with the spoke adjusting wrench (B). If
the wheel rim is curved or bent it must be re-
placed.

NOTE

NOTE

NOTE

NOTE

A welded area on the rim may indicate excessive run out. Disregard this when measuring rim run out.

Wheels

«
...
26
27
28
29
30
...
»

Содержание AWD 250





























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 250

Бренд: Free Spirits Страницы: 32

Бренд: Can-Am Страницы: 16

Бренд: Can-Am Страницы: 254

EC-SIX DAYS - PART LIST 2011

Бренд: GAS GAS Страницы: 6

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

PowerCom INNOVA Plus Business

Бренд: AKE Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: DYNATEK Страницы: 5

Бренд: DYNATEK Страницы: 12

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 8

Burromini-Gas TT40

Бренд: Burro Max Страницы: 34

Бренд: R&G Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды