manualshive.com logo in svg

Christie LED012-CP-R, Инструкция по установке и настройке

Поделиться
Скачать
Christie LED012-CP-R Скачать руководство пользователя страница 18

Installation and setup

The configuration of an array depends on the installation. Use the following instructions as a guideline

only. Before you install an LED array, you must fully understand all site requirements and

characteristics.

A

Chassis

B

LED modules

Installing an LED array from the front

Perform the following steps when you install an LED array while facing the LED modules.

1. Install the mounting pads (on page 19).
2. Mount the tiles (A) (on page 21).
3. Connect the data cables (on page 23).
4. Connect the power cables between tiles (on page 24).
5. Reinstall the LED modules (B) (on page 24).
6. Install and configure the Remote Power Supply Rack Shelf (on page 25).
7. Connect the tile power cables to the Remote Power Supply Rack Shelf (on page 25).
8. Connect the data cables to the video sources (on page 28).
9. Power on the array (on page 29).
10. Install the controller software.

•

Install the E500 controller software (on page 31).

•

Install the E600 controller software (on page 35).

11. Configure the controller.

•

Configure the E500 controller (on page 31).

•

Configure the E600 controller (on page 35).

 

Velvet LED Display System Installation and Setup Guide–CorePlus Series (Remote Power)

18

020-102423-01 Rev. 1 (06-2018)

Copyright 

©

 2018 Christie Digital Systems USA, Inc. All rights reserved.

Содержание LED012-CP-R












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды