manualshive.com logo in svg

Christie LED012-CP-R, Инструкция по установке и настройке

Поделиться
Скачать
Christie LED012-CP-R Скачать руководство пользователя страница 33

4. Click Read from HW.
5. Review the configuration of the tiles in the array, and modify as needed.

The cable layout for the tiles in the array is identified with an S where the first cable starts,
and the green line shows the path of the daisy chain of cables. E identifies the end of the daisy
chain.

Setting the input resolution

Set the resolution for the home page display of interface, which must be consistent with the output

resolution of the video source.

1. Log into the E500 controller software.
2. Click Screen Configuration.
3. Select Configure Screen and click Next.
4. Switch to the Sending Card tab.
5. In the Set the Sending Card Display Mode section, select the resolution of the video source

from the Resolution list.

6. Click Save.

Locking and unlocking the controller

Disable the ability to navigate the menu and modify the settings from the front of the controller.

1. To disable access to the controller menu, press and hold the menu dial and back button until

the controller screen flashes.

2. To re-enable access to the controller menu, press and hold the menu dial and back button for

approximately 15 seconds.

3. Test if the controller is unlocked by using the menu dial to navigate the menu.

If the controller is still locked, press and hold the menu dial and back button for a longer
period of time.

Upgrading the firmware on the E500 controller

When a new version of the software is released, the E500 controller must be upgraded.

1. Download the firmware file to a computer that will be connected to the controller for the

upgrade, or to a USB key.

2. Unzip the downloaded firmware file.
3. Connect an HDMI or Ethernet cable between the computer running the controller software and

the controller.

4. Launch the E500 controller software and log in as the administrator.

a) Click User > Advanced User Login.
b) Login with the password admin.

5. In the blank area beside the Monitoring icon, right-click and type 666888.

Configuring the E500 controller

Velvet LED Display System Installation and Setup Guide–CorePlus Series (Remote Power)

33

020-102423-01 Rev. 1 (06-2018)

Copyright 

©

 2018 Christie Digital Systems USA, Inc. All rights reserved.

Содержание LED012-CP-R












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды