manualshive.com logo in svg

Christie LED012-CP-R, Инструкция по установке и настройке

Поделиться
Скачать
Christie LED012-CP-R Скачать руководство пользователя страница 15

Inputs/Outputs

Description

Total loading capacity: 8.8 million pixels
Low latency is not supported

B

Control

Ethernet

USB, RJ45 (with SNMP support), and USB cascading

C

USB Out

D

USB In

E

Genlock

BNC (Qty. 2)

Support Genlock IN & LOOP

F

Inputs

DisplayPort

Standard DisplayPort 1.2 input
The maximum user-definable resolution is 7680 x 1080 @ 60Hz or
1080 x 6000 @ 60Hz.

G

HDMI

Standard HDMI 2.0 input
Supports 8 bit, 10 bit, and 12 bit; refer to the table below.

H

DVI (Qty. 2)

Dual-link DVI, user-definable resolution

• Horizontal resolution maximum: 3840 pixels

• Vertical resolution maximum 3840 pixels

I

OPT Output

Fiber optic ports for connecting to the FE600 fiber optic extender

J

Power

Power supply port: AC 100-240V~ 50/60hz

K

Power switch

HDMI 8 bit, 10 bit, and 12 bit support

Color depth

Input source

3840 x 2160 @
60Hz (HDCP)

3840 x 1080 @
60Hz (HDCP)

1920 x 1080 @
60Hz (HDCP)

8 bit

RGB444

Yes

Yes

Yes

YCbCr444

Yes

Yes

Yes

YCbCr422

Yes

Yes

Yes

YCbCr420

Yes

Yes

Yes

10 bit

RGB444

No

Yes

Yes

YCbCr444

No

Yes

Yes

YCbCr422

Yes

Yes

Yes

YCbCr420

Yes

Yes

Yes

12 bit

RGB444

No

Yes

Yes

YCbCr444

No

Yes

Yes

Product overview

Velvet LED Display System Installation and Setup Guide–CorePlus Series (Remote Power)

15

020-102423-01 Rev. 1 (06-2018)

Copyright 

©

 2018 Christie Digital Systems USA, Inc. All rights reserved.

Содержание LED012-CP-R












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды