Chint Power CPS PSW1.5M-1500V Скачать руководство пользователя страница 30

Страница: 30 / 84

situations on site.

WARNING:

After the flashings are installed, the joint between the flashings and the container must

be well sealed.

NOTICE:

The cover plate and the flashings are heavy; therefore, please make sure this

procedure is performed by at least two persons.

Proceed as follows to install the flashings:

Step 1 Remove the cover plate on the upper side of the container left and right sides;

Step 2 Mount the flashings;

Step 3 Joints between the flashings and container must be sealed to prevent air or water leakage.

The sealing materials used must be able to withstand temperature of at least 70

℃

5.6.2 Installation Steps

Proceed as follows to install the flashing.

Step Figure

Description

Remove the sealing plate.

Remove the sealing plate before installing the flashing. Unscrew

the fastening screws around the plate to remove the plate.

Figure in the left is the view after the plate is removed.

Install the flashing.

Install the flashing to the pre-set position.

Screw all the tightening screws that connect the flashing to the

container.

Seal the flashing.

Seal the gaps in-between the flashing and the container properly

using the waterproof glue.

Please buy waterproof glue by oneself.

Installation completes.

Figure in the left is the front view of the product after the

flashing is installed.

Содержание CPS PSW1.5M-1500V





















































































Результаты поиска

Содержание CPS PSW1.5M-1500V

Отзывы:

Похожие инструкции для CPS PSW1.5M-1500V

Бренды по названию

Популярные бренды

Chint Power CPS PSW1.5M-1500V, Руководство пользователя

Результаты поиска

Содержание CPS PSW1.5M-1500V

Отзывы:

Похожие инструкции для CPS PSW1.5M-1500V

Бренды по названию

Популярные бренды