Challenge CHAMPION 305 TC Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 110

background image

11.0 Hydraulic System

32

Figure 21

3. Using a hand drill and transfer pump commonly found at hardware and home improvement

stores, transfer the used oil to empty containers.

4. Remove the magnet stuck to the bottom of the tank. Clean off any debris that may be

attached to it.

5. With a clean rag, wipe out any visible debris remaining in the tank.

6. Place the magnet at the location from which it was removed.

7. Replace the oil filter. Place a thin film of new hydraulic oil on the seal of the new filter to

insure a proper seal. Firmly hand-tighten the filter onto the filter head.

8. Using the transfer pump, fill the tank with 13.5 gallons of the recommended fluid (See Section

11.1 - Recommended Hydraulic Oil) until the level is just above the sight gauge shown in
Figure 21.

9. Re-install the tank cover with gasket.

10. Before turning on the machine, make sure all hydraulic hose fittings are tight.

11. Turn on main power to the machine. Turn on the hydraulic motor by pressing both cut buttons

once. Inspect the hydraulic system for leaks. If leaks are found, turn off main power to the
machine and tighten any leaking fittings.

11.3 Hydraulic Valve Adjustments

Several of the following tests require the machine to be operational for

checking and adjusting. Be very careful that tools and other people are clear of moving parts and that
the cutter is not accidentally operated while adjustments are being made. Disconnect the power and
lock it out, (see Safety Precautions, page 5) whenever working on the machine unless the directions
specifically require the machine to be powered.

NOTE: Pressure settings fluctuate with oil temperature. Set pressures when the oil is hot.

Sight
Gauge

Hydraulic
Tank

Reservoir

Tank Cover

«
...
30
31
32
33
34
...
»

Содержание CHAMPION 305 TC















































































































Отзывы:

Нет отзывов

Похожие инструкции для CHAMPION 305 TC

Бренд: Xtool Страницы: 5

GATOR EK425LXCJACSR

Бренд: Greenlee Страницы: 20

Бренд: Mega Machine Страницы: 29

Mat Master 1060B System

Бренд: FrameCo Страницы: 12

Бренд: Mafell Страницы: 57

Бренд: Hallde Страницы: 44

K 650/700 Active

Бренд: Partner Страницы: 96

Бренд: Laser Key Products Страницы: 55

Бренд: Grafalex Страницы: 13

Бренд: Krone Страницы: 66

Бренд: Valex Страницы: 28

Бренд: Mafell Страницы: 58

Бренд: Land Pride Страницы: 172

Бренд: Xhorse Страницы: 20

Бренд: Mafell Страницы: 34

Бренд: Zenoah Страницы: 59

Бренд: Zenoah Страницы: 28

Бренд: EMAK Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды