Challenge CHAMPION 305 TC Скачать руководство пользователя страница 3

Страница: 3 / 110

1.0 Introduction

TABLE OF CONTENTS

1.0 Introduction ...................................................................................................................................... 2

2.0 Safety ............................................................................................................................................... 5

2.1 Precautions .................................................................................................................................. 5

2.2 Power Lockout Procedure ........................................................................................................... 5

2.3 Warning Label Definitions............................................................................................................ 6

3.0 Packing List...................................................................................................................................... 8

4.0 Specifications ................................................................................................................................... 9

5.0 Footprint ......................................................................................................................................... 10

6.0 Installation & Setup ........................................................................................................................ 11

6.1 Inspecting Shipment .................................................................................................................. 11

6.2 Uncrating ................................................................................................................................... 11

6.3 Lifting/Moving Instructions ......................................................................................................... 11

6.4 Cleaning..................................................................................................................................... 12

6.5 Assembly ................................................................................................................................... 12

6.6 Hydraulic Power Unit Removal.................................................................................................. 13

6.7 Hydraulic Check......................................................................................................................... 13

6.8 Power Hook-Up ......................................................................................................................... 14

7.0 Operation ....................................................................................................................................... 16

7.1 False Clamp Plate ..................................................................................................................... 16

8.0 Knife Installation/Changing ............................................................................................................ 18

8.1 Knife Removal ........................................................................................................................... 19

8.2 Knife Installation ........................................................................................................................ 20

8.3 Knife Care Tips .......................................................................................................................... 22

8.3.1 Knife Blade Life .................................................................................................................. 22

8.3.2 Cutting Stick ....................................................................................................................... 23

8.3.3 Bevel Angle ........................................................................................................................ 23

8.3.4 Helpful Suggestions ........................................................................................................... 23

8.3.5 Knife Care .......................................................................................................................... 23

Maintenance Section ......................................................................................................................... 25

9.0 Cleaning ......................................................................................................................................... 26

9.1 Table .......................................................................................................................................... 26

9.2 Console...................................................................................................................................... 27

9.3 Machine Frame.......................................................................................................................... 27

10.0 Lubrication.................................................................................................................................... 28

11.0 Hydraulic System ......................................................................................................................... 31

11.1 Recommended Hydraulic Oil................................................................................................... 31

11.2 Changing the Oil ...................................................................................................................... 31

11.3 Hydraulic Valve Adjustments ................................................................................................... 32

12.0 Adjustments ................................................................................................................................. 37

12.1 Electric Eye Alignment............................................................................................................. 37

12.2 Backgauge Gib Adjustment ..................................................................................................... 38

12.3 Squaring the Backgauge ......................................................................................................... 39

12.4 Backgauge Position Accuracy Adjustment .............................................................................. 40

12.5 Knife Latch Adjustment............................................................................................................ 41

12.6 Line Light Adjustment (Incandescent Type) ............................................................................ 42

12.7 Line Light Adjustment (LED Type)........................................................................................... 43

12.8 Proximity Switches................................................................................................................... 44

12.9 Clamp Return Speed Adjustment ............................................................................................ 46

12.10 Pre-Clamp Pressure Adjustment ........................................................................................... 46

12.11 Pre-Clamp Speed Adjustment ............................................................................................... 47

Содержание CHAMPION 305 TC















































































































Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды

Challenge CHAMPION 305 TC, Инструкция и каталог запасных частей

Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды