Challenge CHAMPION 305 TC Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 110

background image

12.0 Adjustments

50

12.15 Knife Bar Gibs

The knife bar gibs are two steel-backed UHMW plates located near the left and right ends of the knife
bar that press on the knife bar’s front surface as it travels up and down. If adjusted too tight the knife
may not come down smoothly and/or scoring may occur which could damage the knife bar and gibs.
If too loose, you could get uneven or inaccurate cuts.

There are three socket set screws with jam nuts located on each side of the cutter’s frame that are
used to adjust the gibs (Figure 44). These should be adjusted only when the knife bar is directly
behind the screws being tightened.

Figure 44

To adjust:

1. Start the machine and make a cut. When the knife is half way down, have someone turn off

the machine. The knife bar should be stopped half way across the gibs.

2. Loosen all (6) jam nuts on the gib adjusting screws and back the screws out 1/2 turn.

3. Adjust center (2) screws until snug, not tight, in order to eliminate the air gap between the

knife bar and gib. Then tighten those (2) jam nuts.

4. Turn on the machine and send the knife all the way down using the “Knife Change” feature

found in the Maintenance pull-down menu. Turn off the machine.

5. Adjust the bottom two screws the same way the middle screws were adjusted. Tighten the

jam nuts.

6. Turn on the machine. The knife should return to the up position. Shut the machine off.

7. Adjust the upper (2) gib adjusting screws and tighten the jam nuts.

8. Turn the power back on and cycle the knife several times. Recheck the gibs (repeat steps 2-6

as necessary).

9. Don’t over-tighten the gibs.

10. If the knife bar and gibs get scored, remove only the burrs by scraping and then sanding

smooth.

«
...
48
49
50
51
52
...
»

Содержание CHAMPION 305 TC















































































































Отзывы:

Нет отзывов

Похожие инструкции для CHAMPION 305 TC

Pacemark PM4410

Бренд: Oki Страницы: 118

Бренд: Parkside Страницы: 34

Бренд: Gardenia Страницы: 40

Бренд: Waytex Страницы: 32

Бренд: Festool Страницы: 141

Бренд: Mikasa Страницы: 44

HyDefinition HD4070

Бренд: Hypertherm Страницы: 88

ClassicCut CL710

Бренд: Rexel Страницы: 30

Бренд: Peach Страницы: 34

Бренд: H.K. Porter Страницы: 10

Бренд: Martin Yale Страницы: 8

Бренд: Ozito Страницы: 2

Бренд: Danfoss Страницы: 50

Бренд: Meec tools Страницы: 112

Бренд: Tanaka Страницы: 52

Бренд: Partner Страницы: 18

Бренд: ZIPPER MASCHINEN Страницы: 108

Бренд: ZIPPER MASCHINEN Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды