WARNING!
Do not use accessories which are not specifically designed and
recommended by the tool manufacturer.
Just because the accessory can be attached
to your power tool, it does not assure safe operation.
•
The rated speed of the accessory must be at least equal to the maximum speed marked
on the power tool.
Accessories running faster than their rated speed can break and fly apart.
•
Wear personal protective equipment. Depending on application, use face shield, safety
goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and
workshop apron capable of stopping small abrasive or workpiece fragments.
The eye
protection must be capable of stopping flying debris generated by various operations . The dust
mask or respirator must be capable of filtrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
•
Never place your hand near the rotating accessory.
Accessory may kickback over your
hand.
•
Do not position your body in the area where power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the wheel’s movement at the point of
snagging.
DESCRIPTION OF SYMBOLS
SPARE PARTS
AIR CUT-OFF
TOOL
76.2mm (3”)
INSTRUCTION MANUAL
SPECIFICATIONS
ACO-PRO
Max Air Pressure:
90psi (6Bar)
Av. Air Consumption:
170l/min (6cfm)
No Load Speed:
20,000/min
Wheel Diameter:
76.2mm (3”)
Air Inlet:
1/4“ BSP
Weight:
0.76kg
Guard Lock Nut
SPACOPRO-28
3” Cutting Blade
SPACOPRO-29
Blade Bolt & Washer
SPACOPRO-30A
Spanner
SPACOPRO-33
Spare parts can be ordered from the Special Orders Desk at
your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
Email: [email protected]
Warning
Read instruction
manual
Wear eye protection
No load speed
Wear ear protection
Revolutions or
reciprocation per minute
/min
n
o
GENERAL AIR TOOL SAFETY WARNINGS
AIR CUT-OFF TOOL SAFETY WARNINGS
WARNING!
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a.
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c.
Keep children and bystanders away while operating a power tool.
Distractions can
cause you to lose control.
d.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
e. Check the maximum pressure rating of any tools or accessories that you intend using with
the compressor. The output pressure of the air from the compressor must be regulated so
that it never exceeds the rated pressure of the tool or accessory.
f. Always wear safety goggles or glasses when using the air compressor. Never point the
nozzle of an accessory towards any part of your body or towards another person.
g.
Drain the moisture from the tank daily.
It will help prevent corrosion.
h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator
mask and protective clothing.
i. Air tools should not be used in a potentialy explosive environment.
j. Use safety equipment including safety goggles or shield, ear protection, breathing or
respirator mask and protective clothing.
k.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned
in this Manual will be considered a case of misuse. The user and not the manufacturer
shall be liable for any damage or injury resulting from such cases of misuse.
WARNING!
In the event that an air line is cut or broken, the air supply must be turned off
at the compressor. A broken air line which is not supported is extremely dangerous and
can whip around very quickly, both with the capability of striking people, and blowing foreign
particles into the air.
Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air
supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from
the compressor.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given the supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
•
Do not attach a saw chain woodcarving blade or toothed saw blade.
Such blades create
frequent kickback and loss of control.
•
Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory.
Corners, sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
•
Wheels must be used only for recommended applications. For example: do not grind
with the side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them to shatter.
•
Always use undamaged wheel flanges that are of correct size and shape for your
selected wheel.
Proper wheel flanges support the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
•
Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an
excessive depth of cut.
Overstressing the wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
•
Do not restart the cutting operation in the workpiece. Let the wheel reach full speed
and carefully re-enter the cut.
The wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
KNOW YOUR PRODUCT
1 Cutting Disc
2 Guard
3 Spindle
4 Lock-off Lever
5 On/Off Trigger
6 Air Inlet
