Challenge CHAMPION 305 TC Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 110

background image

1.0 Introduction

2

1.0 Introduction

This manual is designed to help you get the most from your Challenge equipment. Keep this manual
in a safe, convenient place for quick reference by operators and service personnel.

SAFETY ALERT! This symbol means CAUTION: Personal safety

instructions! Pay special attention to the instructions in bold type. Personal injury may result if the
precautions are not read and followed.

READ THIS MANUAL BEFORE OPERATING! Follow the precautions and instructions given. If
after reading the manual questions still remain, contact your Authorized Challenge Dealer.

FOR PARTS AND SERVICE, contact the Authorized Challenge Dealer from whom you purchased
the machine. Use the illustrations and parts lists at the back of this manual to identify the correct
parts needed. Always give the SERIAL NUMBER and MODEL of your machine to insure the correct
parts are sent as soon as possible.

RECORD YOUR MACHINE SERIAL NUMBER in the space provided on the front cover of this
manual. Fill out the warranty card accompanying your machine and return it DIRECTLY TO
CHALLENGE.

If you bought a used machine, it is important to have the following information on record at Challenge.
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125
Norton Center Drive

•

Norton Shores

•

MI 49441.

CHALLENGE MODEL

SERIAL NUMBER

ATTN COMPANY

ADDRESS
CITY STATE/PROVINCE

ZIP

PHONE DATE

INSTALLED

DEALER NAME & CITY

* WARRANTY INFORMATION *

It is very important that you read and understand the conditions outlined in the Warranty Information
Sheet attached to the outside of the shipping container of your machine.

The Warranty Information Sheet must be filled out completely and returned to THE CHALLENGE
MACHINERY COMPANY in order for the warranty to be issued for this machine.

Challenge® is a registered trademark of

The Challenge Machinery Company

•

6125 Norton Center Drive

•

Norton Shores MI 49417

Copyright© 1997-2014 by The Challenge Machinery Company. All rights reserved. Printed in the U.S.A

«
1
2
3
4
...
»

Содержание CHAMPION 305 TC















































































































Отзывы:

Нет отзывов

Похожие инструкции для CHAMPION 305 TC

Бренд: Makita Страницы: 110

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 26

Бренд: ALFRA Страницы: 8

$HP Latex Plus Manual preview$

Бренд: HP Страницы: 56

101 90 47-26 142RB/152RB

Бренд: Husqvarna Страницы: 29

Бренд: Black & Decker Страницы: 116

ICS 701-A Series

Бренд: Diamond Tools Страницы: 29

Бренд: Xtool Страницы: 26

Big Shot Machin

Бренд: SIZZIX Страницы: 26

Бренд: Lervia Страницы: 15

Бренд: Bake Max Страницы: 10

Бренд: Maruyama Страницы: 28

Бренд: Coopers Страницы: 16

Бренд: TASKMASTER TOOLS Страницы: 2

Бренд: Danfoss Страницы: 50

Бренд: Gardol Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды