Challenge CHAMPION 305 TC Скачать руководство пользователя страница 48

Страница: 48 / 110

12.0 Adjustments

12.12 Clamp Cylinder Adjustment (Clamp Height)

If the clamp piston bottoms in the cylinder before the clamp makes contact with the table, or if the
clamp does not make full travel on the up stroke, the clamp cylinder may need adjustment.

To adjust:

1. Turn on machine. Start the hydraulic motor by pressing both cut buttons simultaneously.

Turn off the machine.

2. DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lockout procedure, page 5).

3. Loosen the jam nut (Figure 41).

Figure 41

4. Use the flats on the clamp cylinder shaft to turn the shaft into or out of the clevis as required,

(in decreases, out increases height). The clamp should be set to 4” above the table.

5. Retighten the jam nut securely.

12.13 Clamp Parallel Rod

If the clamp is not parallel with the table:

1. DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lockout procedure, page 5.)

2. Loosen the jam nuts on each end of the clamp connecting rod, (Figure 42). (Note: the left

jam nut has left hand threads.)

Clamp
Cylinder

Clevis

Jam Nut

Wrench Flat

Содержание CHAMPION 305 TC















































































































Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды

Challenge CHAMPION 305 TC, Инструкция и каталог запасных частей

Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды