Challenge CHAMPION 305 TC Скачать руководство пользователя страница 43

Страница: 43 / 110

12.0 Adjustments

To adjust line light:

1. Let the console down by removing the two screws at the top.

2. Place a wide sheet(s) of paper on the cut stick to view the line.

3. Using a 3/16” hex wrench, turn one of the cap screws until you see a 1/16-1/8” beam.

4. Similarly, turn the adjustment screw of the other bulb until one, continuous beam is seen

across the paper on the table.

Bulb replacement:

1. DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lockout procedure, page 5)

2. Lower the console.

3. Remove the old bulb by lightly pushing bulb into the socket and turning it counter-clockwise.

CAUTION!- If the bulb is still hot, allow a few minutes to cool before changing.

4. Insert the new bulb into the socket and twist clockwise until the bulb locks into place.

5. Reattach

the

console.

6. Reconnect the power and turn ON.

7. If necessary, adjust the line as above.

8. Unless the cutter will be operated immediately, turn the power off.

12.7 Line Light Adjustment (LED Type)

The line light comes on whenever main power is turned to the ON position and stays on until the
machine goes into sleep mode. Light reaches the table after passing between the knife and clamp,
(Figure 34).

Figure 34 – L.H. Cut-Away Side View

Содержание CHAMPION 305 TC















































































































Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды

Challenge CHAMPION 305 TC, Инструкция и каталог запасных частей

Результаты поиска

Содержание CHAMPION 305 TC

Отзывы:

Похожие инструкции для CHAMPION 305 TC

Бренды по названию

Популярные бренды