Challenge CHAMPION 305 TC Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 110

background image

13.0 Repair and Replacement

51

13.0 Repair and Replacement

13.1 Fuses

FIRE HAZARD. Replace only with same type and rating fuse.

All Champion models have a set of fuses. The fuses are located inside the main power box, (Figure
45). Check the label on the inside of the lower right door for correct ratings for these fuses. Labels
can be reproduced using the drawings at the back of this manual if the labels on the cover ever
become damaged or illegible.

Figure 45

13.2 Knife Cylinder Replacement

Replacing the Knife Cylinder:

1. Remove the knife from the cutter (see Knife, Installation and Set Up).

2. Place a 3” (60mm) lift of paper under the clamp only to hold it up and out of the way of the

knife bar. Then place a 3’ (1 meter) long 2x4 board flat side down under the right end of the
knife bar. This will be used for leverage on the knife bar when removing and reinstalling the
knife bar pin.

3. Lock the clamp and knife down by following instructions in the Operator Controls section for

your particular model of machine.

4. Turn off the main power disconnect switch. DISCONNECT POWER AND LOCK IT OUT!

See page 5.

Loosen connections slowly to bleed off any trapped pressure!

5. Place a pan underneath the cylinder and gradually loosen and remove the hydraulic hose

connections (Figure 46). Loosen the connections slowly to bleed off any trapped pressure.

Fuses

«
...
49
50
51
52
53
...
»

Содержание CHAMPION 305 TC















































































































Отзывы:

Нет отзывов

Похожие инструкции для CHAMPION 305 TC

Бренд: Officezone Страницы: 6

Bessemer C Series

Бренд: NovaTec Страницы: 40

UNIVERSAL MT0006

Бренд: McCulloch Страницы: 64

Бренд: Erbauer Страницы: 21

Бренд: pellenc Страницы: 42

Бренд: ERM Страницы: 32

Бренд: Ryobi Страницы: 28

Бренд: YATO Страницы: 116

Бренд: YATO Страницы: 60

Бренд: MADER Страницы: 81

Бренд: Zenoah Страницы: 72

Бренд: Land Pride Страницы: 28

Бренд: Tanaka Страницы: 23

Бренд: Ransomes Страницы: 68

Бренд: CanyCom Страницы: 93

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 100

Бренд: Panasonic Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды