Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя | Manualshive

Страница: 55 / 56

background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480267-01

Printed in U.S.A.

Form 48LCB-14-26-02SI

Pg CL-1

9-19

Replaces: 48LCB-14-26-01SI

START-UP CHECKLIST

(Remove and Store in Job File)

I. PRELIMINARY INFORMATION

MODEL NO. ____________________________________________

JOB NAME _____________________________________________

SERIAL NO.. ___________________________________________

ADDRESS _____________________________________________

START-UP DATE________________________________________

TECHNICIAN NAME _____________________________________

ADDITIONAL ACCESSORIES

_____________________________________________________________________________________________________

II. PRE-START-UP

Verify that all packaging materials have been removed from unit (Y/N) _____
Verify installation of duct pressure transducer (Y/N) _____
Verify installation of outdoor air hood (Y/N) _____
Verify installation of flue exhaust and inlet hood (Y/N) _____
Verify that condensate connection is installed per instructions (Y/N) _____
Verify that all electrical connections and terminals are tight (Y/N) _____
Verify gas pressure to unit gas valve is within specified range (Y/N) _____
Check gas piping for leaks (Y/N) _____
Check that indoor-air filters are clean and in place (Y/N) _____
Check that outdoor-air inlet screens are in place (Y/N) _____
Verify that unit is level (Y/N) _____
Check fan wheels and propeller for location in housing/orifice and verify setscrew is tight (Y/N) _____
Verify that fan sheaves are aligned and belts are properly tensioned (Y/N) _____
Verify that scroll compressors are rotating in the correct direction (Y/N) _____
Verify installation of thermostat (Y/N) _____
Verify that crankcase heaters have been energized for at least 24 hours (Y/N) _____

III. START-UP

ELECTRICAL

Supply Voltage

L1-L2_____________

L2-L3_____________

L3-L1_____________

Compressor Amps 1

L1 _____________

L2 _____________

L3 _____________

Compressor Amps 2

L1 _____________

L2 _____________

L3 _____________

Supply Fan Amps

L1 _____________

L2 _____________

L3 _____________

TEMPERATURES

Outdoor-air Temperature

_____________ °F DB (Dry Bulb)

Return-air Temperature

_____________ °F DB

_____________

°

F WB (Wet Bulb)

Cooling Supply Air Temperature

_____________ °F

Gas Heat Supply Air Temperature

_____________ °F

NOTE: To avoid injury to personnel and damage to equipment or

property when completing the procedures listed in this start-up

checklist, use good judgment, follow safe practices, and adhere to

the safety considerations/information as outlined in preceding sec-

tions of this Installation Instruction document.

«
...
53
54
55
56
»

Содержание WeatherExpert 48LC B14 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренд: Daikin Страницы: 42

DUCT09HP230V1BD

Бренд: Gree Страницы: 51

Бренд: Turbo Air Страницы: 21

Бренд: Yoer Страницы: 36

Бренд: ABCOOLAIR Страницы: 24

Бренд: Rowenta Страницы: 44

Therapure TP250

Бренд: Boneco Страницы: 32

Бренд: Industrial Climate Engineering Страницы: 26

Бренд: Best Living Systems Страницы: 16

Бренд: Technibel Страницы: 46

Бренд: Haverland Страницы: 40

Бренд: GE Страницы: 80

Бренд: GE Страницы: 40

Бренд: Daikin Страницы: 46

REYQ72XBTJ Series

Бренд: Daikin Страницы: 49

Бренд: Daikin Страницы: 53

Бренд: Daikin Страницы: 56

REYQ72TAYC Series

Бренд: Daikin Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды