manualshive.com logo in svg

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Поделиться
Скачать
Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя страница 41

41

Fig. 60 — Align Bottom of VFD Keypad with Opening 

in VFD Front Panel

Fig. 61 — Secure Keypad in Place

Using the Cable to Connect the Keypad to the VFD

The VFD keypad can be connected to the variable frequency drive

via the cable included with the Multi-Speed VFD display kit (PN:

CRDISKIT002A00). See Fig. 62.
1. Connect the male end of the cable to the front panel of the

variable frequency drive. Use 2 of the screws included with

the kit to secure the cable to the VFD.

2. Connect the female end of the cable to the back panel of the

VFD Remote keypad. Secure the cable to the remote keypad
using the 2 remaining screws from the kit.

Fig. 62 — VFD Remote Keypad Cable

PROGRAM THE VFD FOR INDOOR FAN CONTROL

NOTE: This procedure requires use of the VFD Keypad which is

included as part of the field-installed Multi-Speed VFD display

kit (PN: CRDISKIT002A00). If the VFD keypad is not already

installed, install it. See “Connecting the Keypad to the VFD” for

details.

To program the VFD for variable indoor fan motor speeds:

1. At Power-Up:

At the first power up the LCD displays the Select Language

screen. The default setting is English (see Fig. 63). To change

the language, press the OK key and use the 

▲

 and

▼

 keys to

scroll to the desired language and then press OK.

NOTE: If English is not the desired language, press OK, select the

desired language and press OK again.

IMPORTANT: 48LC*B14-26 units are programmed at

the factory for variable indoor fan speeds. The following

procedure is only to be used to recover this function after

an event such as a system crash.

Male Connector -
connect to VFD
Front Panel

Female Connector -
connect to back of
VFD Remote Keypad

Содержание WeatherExpert 48LC B14 Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды