Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя

Страница: 42 / 56

Fig. 63 — Keypad with Power Up Screen Displayed

2. Selecting Regional Settings:

a. Press the

Off Reset

key.

b. Press the

Menu

key to move the

▼

(triangle icon) so

it is positioned over Main Menu. The display shows
the following.

c. Press the

key and the display changes to:

NOTE: Press the

Back

key to return to the previous display.

d. With the top row highlighted, press OK. The display

changes to:

e. Press

▼

(Down Arrow key) once; the display changes

to:

f. Press OK; the [0] is now highlighted.

g. Press

▼

(Down Arrow) key once; the display changes

to:

h. Press OK

NOTE: If the Alarm 060 appears, follow Step 3 to clear the alarm.

Make sure to press

Off Reset

when done. If there is no alarm, con-

tinue at Step 4.
3. Clearing Alarm 060: External Interlock:

a. Press the Menu key twice to position the

▼

(triangle

icon) over Main Menu; the display changes to:

b. Press the

▼

(Down Arrow) key until the following

display appears:

c. Press

. The display changes to:

d. Press

▼

(Down Arrow) once to highlight the bottom

row and press OK. The display changes to:

e. Press

▼

(Down Arrow) twice; the following display

appears:

f. Press

to highlight the number in the bracket.

g. Press

▼

(Down Arrow) until the following display

appears:

h. Press

i. Press

Off Reset

. The Alarm indicator disappears.

4. Entering Grid Type:

a. Press the

Menu

key to move the

▼

(triangle icon) so

it is positioned over Main Menu. The display shows

the following:

b. Press

twice; the display changes to:

c. Press

▼

(Down Arrow) three times to reach the fol-

lowing display:

d. Press

to highlight the number in the bracket and

then use the

▲

and

▼

(Up and Down Arrow) keys to

select the desired voltage and Hertz for the unit.

e. Press

to accept the selection and continue.

5. Entering Motor Data:

a. Press the Menu key to move the

▼

(triangle icon) so

it is positioned over Main Menu. The display shows

the following:

b. Press

▼

(Down Arrow) once to highlight the bottom

row.

c. Press

, the display changes to:

d. Press

▼

(Down Arrow) twice to reach the following

display:

e. Press

; the following display appears:

NOTE: The number in the bracket may be different from what is

shown above.

0—** Operation / Display
1—** Load and Motor

0—0* Basic Settings
0—1* Set-up Operations

0—01 Language

[0] English

0—03 Regional Settings

[0] International

0—03 Regional Settings

[1] North America

0—** Operation / Display
1—** Load and Motor

4—** Limits / Warnings
5—** Digital In/Out

Off

Reset

Hand

Alarm

Warn.

Com.

Auto

Status

Quick

Main

Select language English
[0] English

SETUP 1

5—0* Digital I/O Mode
5—1* Digital Inputs

5—10 Terminal 18 Digital In…

[8] Start

5—12 Terminal 27 Digital In…

[7] External Interlock

5—12 Terminal 27 Digital In…

[0] No operation

0—0* Basic Settings
0—1* Set-up Operations

0—01 Language

[0] English

0—06 Grid Type

[102] 200-240V/60Hz

0—** Operation / Display
1—** Load and Motor

1—0* General Settings
1—1* Motor Selection

1—1* Motor Selection
1—2* Motor Data

1-20 Motor Power

[9] 1.5kW - 2 hp

Содержание WeatherExpert 48LC B14 Series

























































Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды