Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя

Страница: 32 / 56

UNITS WITHOUT FACTORY-INSTALLED NON-FUSED

DISCONNECT OR HACR
When installing units, provide a disconnect switch per NEC (Na-

tional Electrical Code) of adequate size. Disconnect sizing data

is provided on the unit informative plate. Locate on unit cabinet

or within sight of the unit per national or local codes. Do not

cover unit informative plate if mounting the disconnect on the

unit cabinet.
UNITS WITH FACTORY-INSTALLED NON-FUSED DIS-

CONNECT OR HACR
The factory-installed option non-fused disconnect switch (NFD)

or HACR is located in the main control box. The manual switch

handle and shaft are shipped in the control box and must be

mounted on the corner post adjacent to the control box (see Fig. 42

or 43). Note that the tape covering the hole for the shaft in the cor-

ner post must be removed prior to handle and shaft installation.

To field install the NFD shaft and handle:

1. Open the control box panel.
2. Make sure the NFD shipped from the factory is at OFF posi-

tion (the arrow on the black handle knob or on the silver

metal collar is at OFF).

3. Insert the shaft with the cross pin on the top of the shaft in the

horizontal position.

4. Measure the tip of the shaft to the outside surface of the cor-

ner post to be 0.88-in.

5. Tighten the locking screw to secure the shaft to the NFD.
6. Turn the handle to OFF position with red arrow pointing at

OFF.

7. Install the handle on to the corner post vertically with the red

arrow pointing up.

8. Secure the handle to the corner post with (2) screws and lock

washers supplied.

To field install the HACR shaft and handle:

1. Open the control box panel.
2. Make sure the HACR shipped from the factory is at OFF

position (the white arrow pointing at OFF).

3. Insert the shaft with the cross pin on the top of the shaft in the

horizontal position.

4. Measure the tip of the shaft to the outside surface of the cor-

ner post to be 0.88-in.

5. Tighten the locking screw to secure the shaft to the HACR.
6. Turn the handle to OFF position with red arrow pointing at

OFF.

7. Install the handle on to the corner post vertically with the red

arrow pointing up.

8. Secure the handle to the corner post with (2) screws and lock

washers supplied.

Fig. 42 — Handle and Shaft Assembly for NFD

Fig. 43 — Handle and Shaft Assembly for HACR

Содержание WeatherExpert 48LC B14 Series

























































Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды